※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
1.1この文書は、力-たわみ図からプラスチックのシャルピー衝撃特性を決定する方法を指定します。 ISO 179-1 では、さまざまな種類の棒状試験片と試験構成、および材料の種類、試験片の種類、ノッチの種類に応じた試験パラメータが定義されています。
この文書では、ロードセル/ストライカーの共振、試験片の共振、初期接触/慣性ピークなどの動的影響について説明します (図 1, 曲線 b, および付録 A を参照)
1.2 ISO 179-1 は、衝撃強度のみによって衝撃挙動を特徴付ける場合、および位置エネルギーが測定対象の特定の破壊エネルギーにほぼ一致する装置を使用する場合に適しています (ISO 13802:2015, 付録 E を参照)この文書は、衝撃挙動の詳細な特性評価のための力とたわみまたは力と時間の図を記録するために、また自動装置を開発するために、つまりエネルギーを一致させる必要性を回避するために使用されます。
このドキュメントで説明されている方法は、次の場合にも適しています。
- 衝撃条件下でより多くの異なる材料特性を獲得する。
- シャルピー試験手順を監督する。この機器を使用すると、試験片がサポートに密着していないなどの典型的な操作ミスを検出できるため。
- 休憩の種類を自動的に検出します。
- 振り子ハンマーの頻繁な交換を避けるための振り子式器具。
- 他の ISO 規格に記載されている破壊の機械的特性を測定します。
1.3この方法で試験できる材料の範囲については、ISO 179-1:2010, 第 1 項を参照してください。
1.4テスト結果の一般的な比較については、ISO 179-1:2010, 第 1 項を参照してください。
1.5材料の典型的な挙動に関する情報は、異なる温度での試験、ノッチ半径および/または試験片の厚さの変更、および異なる条件下で準備された試験片の試験によって得られます。
この文書の目的は、力 - たわみ図のあらゆる点で発生するメカニズムの解釈を提供することではありません。これらの解釈は、進行中の科学研究の課題です。
1.6この方法で得られた試験結果は、試験片の準備条件と試験条件が同じ場合にのみ比較可能です。したがって、完成品の衝撃挙動をこのテストから直接予測することはできません。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 179-1:2010, プラスチック — シャルピー衝撃特性の測定 — Part 1: 計器を使用しない衝撃試験
- ISO 291, プラスチック — 調整および試験用の標準雰囲気
- ISO 2602, テスト結果の統計的解釈 — 平均値の推定 — 信頼区間
- ISO 16012, プラスチック — 試験片の長さ寸法の決定
- ISO 13802:2015, プラスチック — 振り子衝撃試験機の検証 — シャルピー、アイゾットおよび引張衝撃試験
1.1 This document specifies a method for determining Charpy impact properties of plastics from force-deflection diagrams. Different types of rod-shaped test specimens and test configurations, as well as test parameters depending on the type of material, the type of test specimen and the type of notch, are defined in ISO 179-1.
Dynamic effects such as load-cell/striker resonance, test specimen resonance and initial-contact/inertia peaks are described in this document (see Figure 1, Curve b, and Annex A).
1.2 ISO 179-1 is suitable for characterizing the impact behaviour by the impact strength only and for using apparatus whose potential energy is matched approximately to the particular energy to break to be measured (see ISO 13802:2015, Annex E). This document is used to record a force-deflection or force-time diagram for detailed characterization of the impact behaviour, and for developing automatic apparatus, i.e. avoiding the need to match energy.
The method described in this document is also suitable for:
- acquiring more and different materials characteristics under impact conditions;
- supervising the Charpy test procedure, as this instrumentation allows detection of typical operational mistakes, such as the specimen not being in close contact with the supports;
- automatically detecting the type of break;
- pendulum type instruments to avoid frequent changes of pendulum hammers;
- measuring fracture mechanical properties described in other ISO standards.
1.3 For the range of materials which can be tested by this method, see ISO 179-1:2010, Clause 1.
1.4 For the general comparability of test results, see ISO 179-1:2010, Clause 1.
1.5 Information on the typical behaviour of materials can be obtained by testing at different temperatures, by varying the notch radius and/or specimen thickness and by testing specimens prepared under different conditions.
It is not the purpose of this document to give an interpretation of the mechanism occurring at every point on the force-deflection diagram. These interpretations are a task for on-going scientific research.
1.6 The test results obtained with this method are comparable only if the conditions of test specimen preparation, as well as the test conditions, are the same. The impact behaviour of finished products cannot, therefore, be predicted directly from this test.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 179-1:2010, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
- ISO 291, Plastics — Standard atmospheres for conditioning and testing
- ISO 2602, Statistical interpretation of test results — Estimation of the mean — Confidence interval
- ISO 16012, Plastics — Determination of linear dimensions of test specimens
- ISO 13802:2015, Plastics — Verification of pendulum impact-testing machines — Charpy, Izod and tensile impact-testing