この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part 1 部に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を 参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
適合性評価に関連する ISO 固有の用語や表現の意味の説明、および貿易の技術的障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照してください。 序文 — 補足情報 。
この文書を担当する委員会は ISO/TC 219, 床材です。
この第 3 版は、技術的に改訂された第 2 版 (ISO 10361:2012) を廃止し、置き換えるものです。
序章
この国際規格では、繊維製床材の試験片を疲労させ、実験室での摩耗シミュレーションで外観の変化を生じさせるために使用される 2 つの機器について説明しています。
この国際規格は当初、タイプ 2 技術報告書として発行されました。 ISO/TC 219 は、国際規格として発行するために文書を改訂することを決定しました。
1 スコープ
この国際規格は、ベッターマン ドラムまたはヘキサポッド タンブラー テスターの機械的動作を使用して、あらゆる種類の繊維製床材の外観 (表面構造と色) に変化を与える手順について説明しています。他の作用による毛玉や色の変化は含まれません。
これらのドラムテスターによって生じた変化は、該当する評価基準に従って評価されます。
2 規範的参照
- 以下の文書は、全部または一部がこの文書で規範的に参照されており、その適用には不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 139, テキスタイル — コンディショニングおよびテスト用の標準雰囲気
- ISO 868, プラスチックおよびエボナイト — デュロメーターによる押し込み硬さの測定 (ショア硬さ)
- ISO 1957, 機械製繊維床材 — 物理試験用の試験片の選択と切断
- ISO 2424, 繊維製床材 — 語彙
- ISO 9405, 繊維製床材 — 外観の変化の評価
- ISO 7619-1, ゴム、加硫または熱可塑性 — 押し込み硬さの決定 — Part 1: デュロメーター法 (ショア硬さ)
3 用語と定義
この文書の目的には、ISO 2424 で与えられる用語と定義が適用されます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword — Supplementary information .
The committee responsible for this document is ISO/TC 219, Floor coverings.
This third edition cancels and replaces the second edition (ISO 10361:2012), which has been technically revised.
Introduction
This International Standard describes two instruments used for fatiguing textile floor covering specimens and producing changes in appearance in a laboratory simulation of wear.
This International Standard was originally published as a type 2 Technical Report. ISO/TC 219 decided to revise the document for publication as an International Standard.
1 Scope
This International Standard describes procedures that use the mechanical action of a Vettermann drum or a hexapod tumbler tester to produce changes in appearance (surface structure and colour) to all types of textile floor coverings. It does not include pilling or colour changes due to other actions.
Changes produced by these drum testers are assessed in accordance with the applicable assessment standard.
2 Normative references
- The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 139, Textiles — Standard atmospheres for conditioning and testing
- ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
- ISO 1957, Machine-made textile floor coverings — Selection and cutting of specimens for physical tests
- ISO 2424, Textile floor coverings — Vocabulary
- ISO 9405, Textile floor coverings — Assessment of changes in appearance
- ISO 7619-1, Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 1: Durometer method (Shore hardness)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2424 apply.