※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令のPart 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
適合性評価に関連する ISO 固有の用語および表現の意味に関する説明、および技術的貿易障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照して ください 。
この文書を担当する委員会は、ISO/TC 4, 転がり軸受です。
この第 4 版は、主に用語と形式に編集上の変更を加えて技術的に改訂された第 3 版 (ISO 104:2002) を取り消して置き換えます。
1 スコープ
この国際規格は、背面が平らな単方向および複方向スラスト軸受の優先境界寸法を指定しています。
さらに、寸法系列 11, 12, 13, 14, 22, 23, および 24 の軸受のハウジング ワッシャの最小内径と軸ワッシャの最大外径を示します。
単方向スラスト軸受に関するこの国際規格の拡張に関するガイドラインは、附属書 A に示されています。
注記スラストベアリング (背面が平らでない) とシートワッシャーの位置合わせの境界寸法は、ISO 20516 に記載されています。 [2]
2 参考文献
以下のドキュメントの全体または一部は、このドキュメントで規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
このドキュメントの目的のために、ISO 5593 および以下に記載されている用語と定義が適用されます。
3.1
背面がフラットな一方向スラスト軸受
一方向のみのアキシアル荷重を支持するための、背面が平らなスラスト転がり軸受
3.2
背面が平らな複式スラスト軸受
両方向のアキシアル荷重を支持するための平らな背面を備えたスラスト転がり軸受
3.3
中央軸ワッシャー
シャフトに取り付けるための中央ワッシャー
[出典: ISO 20516:2007, 3.5]
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 4, Rolling bearings.
This fourth edition cancels and replaces the third edition (ISO 104:2002), which has been technically revised with changes that are editorial and concern mainly on terminology and format.
1 Scope
This International Standard specifies preferred boundary dimensions for single-direction and double-direction thrust bearings with flat back faces.
In addition, it gives the minimum bore diameters of housing washers and maximum outside diameters of shaft washers of bearings in dimension series 11, 12, 13, 14, 22, 23 and 24.
Guidelines for the extension of this International Standard for single-direction thrust bearings are given in Annex A.
NOTE Boundary dimensions for aligning thrust bearings (none flat back faces) and aligning seat washers are given in ISO 20516.[2]
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 582, Rolling bearings — Chamfer dimensions — Maximum values
- ISO 5593, Rolling bearings — Vocabulary
- ISO 15241, Rolling bearings — Symbols for physical quantities
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5593 and the following apply.
3.1
single-direction thrust bearing with flat back faces
thrust rolling bearing with flat back faces intended to support axial load in one direction only
3.2
double-direction thrust bearing with flat back faces
thrust rolling bearing with flat back faces intended to support axial load in both directions
3.3
central shaft washer
central washer which is intended to be mounted on a shaft
[SOURCE: ISO 20516:2007, 3.5]
Bibliography
| [1] | ISO 3, Preferred numbers — Series of preferred numbers |
| [2] | ISO 20516, Rolling bearings — Aligning thrust ball bearings and aligning seat washers — Boundary dimensions |