※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令、 Part 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令のPart 2 の編集規則に従って起草されました。 www.iso.org/directives
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受け取った特許宣言の ISO リストに記載されます。 www.iso.org/patents
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
この文書を担当する委員会は、ISO/TC 29, 小型工具、小委員会 SC 2, 高速度鋼切削工具および付属品です。
この第 2 版は、第 1 版 (ISO 10649-1:2010) を取り消して置き換えたものであり、以下の変更を含むマイナー リビジョンを構成しています。
- ISO 10649 のこの部分の記号と ISO 13399 シリーズによる記号との関係を示す附属書 A の追加。
ISO 10649 は、次の部分で構成されており、一般的なタイトルは、平行キーとほぞドライブを備えたカッター アーバーです。
- Part 1: 一般寸法
- Part 2: フランジ接触面を備えたテーパー インターフェースを備えたツール ホルダーの寸法と名称
- Part 3: 自動ツール チェンジャー用 7/24 テーパーのツール ホルダーの寸法と名称
- Part 4: 自動ツール チェンジャーなしの 7/24 テーパーのツール ホルダーの寸法と名称
- Part 5: フランジ接触面を備えたポリゴン テーパー インターフェースを備えたツール ホルダーの寸法と名称
- Part 6: ボール トラック システムを備えたモジュラー テーパー インターフェースを備えたツール ホルダーの寸法と名称
序章
ISO 10649 (すべての部品) の目的は、このタイプのインターフェース用のツール ホルダーの主な寸法を指定し、工作機械内で組み立てられたツールを交換する際の衝突のリスクを防ぐことです。
1 スコープ
ISO 10649 のこのパートでは、平行キーとほぞドライブを備えたカッター アーバーのツール インターフェースの寸法を指定しています。
2 参考文献
以下のドキュメントの全体または一部は、このドキュメントで規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 2768-1, 一般公差 — Part 1: 個々の公差表示のない直線および角度寸法の公差
- ISO 2768-2, 一般公差 — Part 2: 個々の公差表示のないフィーチャの幾何公差
- ISO 2780, ほぞドライブ付きフライスカッター — カッターアーバーの互換性寸法 — メートル系
- ISO 10643, 平行キーおよびほぞドライブ付きカッター アーバーのアクセサリの寸法
参考文献
| [1] | ISO 1339, 切削工具データの表示と交換 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, High speed steel cutting tools and their attachments.
This second edition cancels and replaces the first edition (ISO 10649-1:2010), of which it constitutes a minor revision with the following changes:
- addition of Annex A, which gives the relationship between the symbols of this part of ISO 10649 and the symbols according to the ISO 13399 series.
ISO 10649 consists of the following parts, under the general title Cutter arbors with parallel key and tenon drive:
- Part 1: General dimensions
- Part 2: Dimensions and designation of tool holders with taper interface with flange contact surface
- Part 3: Dimensions and designation of tool holders with 7/24 taper for automatic tool changer
- Part 4: Dimensions and designation of tool holders with 7/24 taper without automatic tool changer
- Part 5: Dimensions and designation of tool holders with polygonal taper interface with flange contact surface
- Part 6: Dimensions and designation of tool holders with modular taper interface with ball track system
Introduction
The aim of ISO 10649 (all parts) is to specify the main dimensions for tool holders for this type of interface, and prevent the risk of collision when exchanging the assembled tool within the machine tools.
1 Scope
This part of ISO 10649 specifies the dimensions of tool interface for cutter arbors with parallel key and tenon drive.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
- ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications
- ISO 2780, Milling cutters with tenon drive — Interchangeability dimensions for cutter arbors — Metric series
- ISO 10643, Dimensions of accessories for cutter arbors with parallel key and tenon drive
Bibliography
| [1] | ISO 13399 (all parts), Cutting tool data representation and exchange |