この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令のPart 2 部で規定されている規則に従って作成されます。
技術委員会の主な任務は、国際規格を準備することです。技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。
ISO 12162 は、技術委員会 ISO/TC 138, 流体輸送用のプラスチック パイプ、継手およびバルブ、小委員会 SC 5, プラスチック材料のパイプ、継手およびバルブの一般的特性およびそれらの付属品 — 試験方法および基本仕様によって作成されました。
この第 2 版は、技術的に改訂された第 1 版 (ISO 12162:1995) を取り消して置き換えるものです。
序章
この国際規格の改訂では、MRS 分類および追加材料の最小設計係数の導入に加えて、CRS θ 、 t値 (温度θおよび時間tでの要求強度を分類) の導入が組み込まれています。
この国際規格の分類は、特定の用途について材料を修飾するものではありません。特定のアプリケーションでは、関連する製品規格により、追加の機械的および物理的特性を満たすことが要求されます。
1 スコープ
この国際規格は、パイプ形状の熱可塑性材料の分類を確立し、材料の指定を指定します。また、設計応力の計算方法も指定します。
圧力用途のパイプおよび継手用の材料に適用できます。
注記 1分類、最小設計係数および計算方法は、ISO 9080 で与えられた方法を使用して外挿することにより導き出された、20 °C の水で 50 年間の内圧に対する抵抗に基づいています。
注記 2多層パイプの設計係数は、該当する製品 (システム) 規格に記載されています。
2 参考文献
本書の適用には、以下の参考文献が不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 1043-1, プラスチック - 記号と略語 - Part 1: 基本ポリマーとその特殊な特性
- ISO 9080, プラスチック配管およびダクトシステム - 外挿によるパイプ形状の熱可塑性材料の長期静水圧強度の決定
3 用語と定義
このドキュメントでは、次の用語と定義が適用されます。
3.1
長期静水圧強度
σLTHS_
温度θおよび時間tでの予測平均強度を表す、応力の次元を持つ量
注記1量はメガパスカルで表す。
注記2温度θは摂氏で表され、時間tは年で表される。
3.2
予測される静水圧強度の信頼限界の下限
σLPL_
温度θおよび時間tで予測される静水圧強度の 97.5% 信頼下限を表す、応力の次元を持つ量
注記1量はメガパスカルで表す。
注記2温度θは摂氏で表され、時間tは年で表される。
3.3
最低必要強度 MRS
20℃、50年におけるσLPLの値で、 R10シリーズまたはR20シリーズのいずれか小さい方の値に切り捨て
注記 1: R10 シリーズは ISO 3 [1]に準拠し、R20 シリーズは ISO 497 [2]に準拠しています。
3.4
温度θと時間t必要強度の分類
CRS θ , t
温度θ 、時間tにおけるσLPLの値で、R10シリーズまたはR20シリーズのいずれか小さい方の値に切り捨てたもの
注記 1: 20 °C および 50 年の CRS θtは MRS に等しい。
注記2温度θは摂氏で表され、時間tは年で表される。
注記 3: R10 シリーズは ISO 3 [1]に準拠し、R20 シリーズは ISO 497 [2]に準拠しています。
3.5
設計係数
C
1より大きい値を持つ係数。下側信頼限界で表されるもの以外の配管システムの構成要素の特性だけでなく、使用条件も考慮に入れる
注記 1: C の最小値CCは、箇条 6 で定義され、さまざまな熱可塑性パイプ システムに対して与えられます。
注記 2:特定のアプリケーションの設計係数は、関連する製品 (システム) 規格で指定されています。
3.6 設計応力
3.6.1
MRS分類に基づく設計応力
σss
MRS を設計係数Cで割って得られる応力、すなわちσs = MRS/ C
注記 1特定の材料の最大許容設計応力は、MRS を最小設計係数Cminで割ることによって得られます。つまり、 σs = MRS/ Cminです。
注記 2:特定のアプリケーションに対する設計応力は、関連する製品 (システム) 規格で指定されています。
3.6.2
CRS θ , t値に基づく設計応力
σs、θ、t
CRS θ , tを設計係数Cで割って得られる応力、すなわちσs,θ,t = CRS θ,t/ C
注記 1所定の材料の最大許容設計応力は、CRS θ , tを最小設計係数Cminで割ることによって得られます。つまり、 σs,θ , t = CRS θ , t/ Cminです。
注記 2:特定のアプリケーションに対する設計応力は、関連する製品 (システム) 規格で指定されています。
参考文献
| [1] | ISO 3, 優先番号 ― 一連の優先番号 |
| [2] | ISO 497, 一連の好ましい数値、および好ましい数値のより丸められた値を含む系列の選択に関するガイド |
| [3] | ISO 10508, 温水および冷水設備用プラスチック配管システム - 分類および設計のガイダンス |
| [4] | ISO 16422:2006, 圧力下で水を搬送するための配向された非可塑化ポリ(塩化ビニル) (PVC-O) 製のパイプおよびジョイント - 仕様 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12162 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories — Test methods and basic specifications.
This second edition cancels and replaces the first edition (ISO 12162:1995), which has been technically revised.
Introduction
The revision of this International Standard incorporates the introduction of a CRS θ, t value (categorized required strength at a temperature θ and time t ), in addition to the MRS classification and the introduction of minimum design coefficients for additional materials.
The classification in this International Standard does not qualify a material for a specific application. For specific applications, the relevant product standards require that additional mechanical and physical properties be met.
1 Scope
This International Standard establishes the classification of thermoplastics materials in pipe form and specifies the material designation. It also specifies a method for calculating the design stress.
It is applicable to materials intended for pipes and fittings for pressure applications.
NOTE 1 Classification, minimum design coefficient and calculation method are based on the resistance to internal pressure with water at 20 °C for 50 years, derived by extrapolation using the method given in ISO 9080.
NOTE 2 Design coefficients for multilayer pipes are described in the appropriate product (system) standards.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 1043-1, Plastics ― Symbols and abbreviated terms ― Part 1: Basic polymers and their special characteristics
- ISO 9080, Plastics piping and ducting systems ― Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
long-term hydrostatic strength
σLTHS
quantity, with the dimension of stress, which represents the predicted mean strength at a temperature θ and time t
Note 1 to entry: The quantity is expressed in megapascals.
Note 2 to entry: Temperature, θ, is expressed in degrees Celsius and time, t , is expressed in years.
3.2
lower confidence limit of the predicted hydrostatic strength
σLPL
quantity, with the dimensions of stress, which represents the 97,5 % lower confidence limit of the predicted hydrostatic strength at a temperature θ and time t
Note 1 to entry: The quantity is expressed in megapascals.
Note 2 to entry: Temperature, θ, is expressed in degrees Celsius and time, t , is expressed in years.
3.3
minimum required strength MRS
value of σLPL at 20 °C and 50 years, rounded down to the next smaller value of the R10 series or the R20 series
Note 1 to entry: The R10 series conforms to ISO 3 [1] and the R20 series conforms to ISO 497 [2] .
3.4
categorized required strength at temperature θ and time t
CRS θ, t
value of σLPL at temperature θ and time t , rounded down to the next smaller value of the R10 series or the R20 series
Note 1 to entry: CRS θ,t at 20 °C and 50 years equals MRS.
Note 2 to entry: Temperature, θ, is expressed in degrees Celsius and time, t , is expressed in years.
Note 3 to entry: The R10 series conforms to ISO 3 [1] and the R20 series conforms to ISO 497 [2] .
3.5
design coefficient
C
coefficient with a value greater than 1, which takes into consideration service conditions as well as properties of the components of a piping system other than those represented in the lower confidence limit
Note 1 to entry: The minimum value of C, Cmin, is defined and given for various thermoplastics pipe systems in Clause 6.
Note 2 to entry: The design coefficient for a given application is specified in the relevant product (system) standard.
3.6 Design stress
3.6.1
design stress based on MRS classification
σs
stress derived by dividing MRS by the design coefficient C , i.e. σs = MRS/ C
Note 1 to entry: The maximum allowable design stress for a given material is derived by dividing MRS by the minimum design coefficient, Cmin, i.e. σs = MRS/ Cmin.
Note 2 to entry: Design stress for a specific application is specified in the relevant product (system) standard.
3.6.2
design stress based on CRS θ, t value
σs ,θ, t
stress derived by dividing CRS θ, t by the design coefficient C , i.e. σs,θ,t = CRS θ,t/ C
Note 1 to entry: The maximum allowable design stress for a given material is derived by dividing CRS θ, t by the minimum design coefficient, Cmin, i.e. σs,θ, t = CRS θ, t/ Cmin.
Note 2 to entry: Design stress for a specific application is specified in the relevant product (system) standard.
Bibliography
| [1] | ISO 3, Preferred numbers ― Series of preferred numbers |
| [2] | ISO 497, Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| [3] | ISO 10508, Plastics piping systems for hot and cold water installations ― Guidance for classification and design |
| [4] | ISO 16422:2006, Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure ― Specifications |