ISO 13232-3:2005 モーターサイクル—モーターサイクルに取り付けられたライダーの衝突保護装置の研究評価のためのテストおよび分析手順—パート3：モーターサイクリストの人体測定衝撃ダミー | ページ 2

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

ISO 13232-3 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 22, Motorcycles.

This second edition cancels and replaces the first version (ISO 13232-3:1996), which has been technically revised.

ISO 13232 consists of the following parts, under the general title Motorcycles — Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles:

• Part 1: Definitions, symbols and general considerations
• Part 2: Definition of impact conditions in relation to accident data
• Part 3: Motorcyclist anthropometric impact dummy
• Part 4: Variables to be measured, instrumentation and measurement procedures
• Part 5: Injury indices and risk/benefit analysis
• Part 6: Full-scale impact-test procedures
• Part 7: Standardized procedures for performing computer simulations of motorcycle impact tests
• Part 8: Documentation and reports

Introduction

ISO 13232 has been prepared on the basis of existing technology. Its purpose is to define common research methods and a means for making an overall evaluation of the effect that devices which are fitted to motorcycles and intended for the crash protection of riders, have on injuries, when assessed over a range of impact conditions which are based on accident data.

It is intended that all of the methods and recommendations contained in ISO 13232 should be used in all basic feasibility research. However, researchers should also consider variations in the specified conditions (for example, rider size) when evaluating the overall feasibility of any protective device. In addition, researchers may wish to vary or extend elements of the methodology in order to research issues which are of particular interest to them. In all such cases which go beyond the basic research, if reference is to be made to ISO 13232, a clear explanation of how the used procedures differ from the basic methodology should be provided.

ISO 13232 was prepared by ISO/TC 22/SC 22 at the request of the United Nations Economic Commission for Europe Group for Road Vehicle General Safety (UN/ECE/TRANS/SCI/WP29/GRSG), based on original working documents submitted by the International Motorcycle Manufacturers Association (IMMA), and comprising eight interrelated parts.

This revision of ISO 13232 incorporates extensive technical amendments throughout all the parts, resulting from extensive experience with the standard and the development of improved research methods.

In order to apply ISO 13232 properly, it is strongly recommended that all eight parts be used together, particularly if the results are to be published.

1 Scope

This part of ISO 13232 specifies the minimum requirements for the:

• biofidelity of the motorcyclist anthropometric impact dummy;
• compatibility of the dummy with motorcycles, helmets, multi-directional impacts, and the instrumentation;
• repeatability and reproducibility of the dummy properties and responses.

ISO 13232 specifies minimum requirements for research into the feasibility of protective devices fitted to motorcycles, which are intended to protect the rider in the event of a collision.

ISO 13232 is applicable to impact tests involving:

• two-wheeled motorcycles;
• the specified type of opposing vehicle;
• either a stationary and a moving vehicle or two moving vehicles;
• for any moving vehicle, a steady speed and straight-line motion immediately prior to impact;
• one helmeted dummy in a normal seating position on an upright motorcycle;
• the measurement of the potential for specified types of injury, by body region;
• evaluation of the results of paired impact tests (i.e. comparisons between motorcycles fitted and not fitted with the proposed devices).

ISO 13232 does not apply to testing for regulatory or legislative purposes.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

3 Definitions

The following terms are defined in ISO 13232-1. For the purposes of this part of ISO 13232, those definitions apply. Additional definitions which could apply to this part of ISO 13232 are also listed in ISO 13232-1:

• abdominal foam insert;
• alternative products;
• certification, compliance;
• knee compliance element;
• load cell simulator;
• lot;
• specimen.