この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の開発に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2 ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自主的な性質に関する説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、次を参照してください。次の URL: www.iso.org/iso/foreword.html
この文書は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 2, 試験および分析によって作成されました。
この第 6 版は、第 5 版 (ISO 132:2011) を取り消して置き換えるものであり、第 2 節の規範的参照を更新し、タイトルと図 1 のキーを改善するためのマイナーな改訂を構成します。
序章
ゴムを繰り返し曲げたり曲げたりすると、曲げ時に引張応力が設定される表面の部分に亀裂が発生するか、表面のこの部分に亀裂が含まれている場合、この亀裂が応力に垂直な方向に伸びます。ある種の軟質加硫物、例えばスチレン-ブタジエンゴムから調製されたものは、亀裂の発生に対して顕著な耐性を示しますが、これらの加硫物は亀裂の成長 (伝播) に対する耐性が低い可能性があります。したがって、曲げによる亀裂の発生に対する耐性と亀裂の伝播に対する耐性の両方を測定することが重要です。
この方法は、少なくとも一定期間のサイクルの後、適度に安定した応力-ひずみ特性を持ち、過度の応力緩和や硬化、または高粘性挙動を示さないゴムに適しています。一部の熱可塑性ゴムで得られた結果は、降伏時の伸びが試験中に加えられた最大ひずみを下回るか、それに近い場合は注意して取り扱う必要があります。
警告 1このドキュメントを使用する人は、通常の実験室の慣行に精通している必要があります。このドキュメントは、その使用に関連する安全上の問題のすべてに対処することを目的としていません。適切な安全衛生慣行を確立し、国内の規制条件を確実に遵守することは、ユーザーの責任です。
警告 2このドキュメントで指定されている特定の手順には、地域の環境に危険を及ぼす可能性のある物質の使用または生成、または廃棄物の生成が含まれる場合があります。使用後の安全な取り扱いと廃棄に関する適切な文書を参照する必要があります。
1 スコープ
この文書は、加硫ゴムまたは熱可塑性ゴムの耐性を、De Mattia タイプの機械で繰り返し曲げたときの亀裂の形成および成長と比較するために使用することを意図した試験方法を指定しています。亀裂の成長を測定するために、試験片に人工的な切り込みを入れて切り込みの成長を開始させます。
2 参考文献
以下のドキュメントは、その内容の一部またはすべてがこのドキュメントの要件を構成するように、テキスト内で参照されています。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 18899:2013, ゴム - 試験装置の校正ガイド
- ISO 23529, ゴム — 物理的試験方法のための試験片の準備とコンディショニングの一般的な手順
3 用語と定義
このドキュメントには、用語と定義は記載されていません。
ISO と IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
参考文献
| [1] | ISO/TR 9272:2005, ゴムおよびゴム製品 - 試験方法規格の精度の決定 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis.
This sixth edition cancels and replaces the fifth edition (ISO 132:2011), of which it constitutes a minor revision to update normative references in Clause 2 and improve the title and the key for Figure 1.
Introduction
Repeated bending or flexing of a rubber causes cracks to develop in that part of the surface where tension stress is set up during flexing or, if this part of the surface contains a crack, causes this crack to extend in a direction perpendicular to the stress. Certain soft vulcanizates, for instance those prepared from styrene-butadiene rubber, show marked resistance to crack initiation, but it is possible for these vulcanizates to have a low resistance to growth (propagation) of cracks. It is important, therefore, to measure both the resistance to crack initiation by flexing and the resistance to crack propagation.
The method is suitable for rubbers that have reasonably stable stress-strain properties, at least after a period of cycling, and do not show undue stress softening or set, or highly viscous behaviour. The results obtained for some thermoplastic rubbers should be treated with caution if the elongation at yield is below, or close to, the maximum strain imposed during the test.
WARNING 1 Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.
WARNING 2 Certain procedures specified in this document might involve the use or generation of substances, or the generation of waste, that could constitute a local environmental hazard. Reference should be made to appropriate documentation on safe handling and disposal after use.
1 Scope
This document specifies a method of test intended for use in comparing the resistance of vulcanized or thermoplastic rubbers to the formation and growth of cracks, when subjected to repeated flexing on the De Mattia type machine. For determination of crack growth, an artificial cut is made in the test piece to initiate cut growth.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 18899:2013, Rubber — Guide to the calibration of test equipment
- ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
Bibliography
| [1] | ISO/TR 9272:2005, Rubber and rubber products — Determination of precision for test method standards |