※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令のPart 3 に規定されている規則に従って起草されています。
技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
この国際規格の一部の要素が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。
国際規格 ISO 13362 は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 4, 製品 (ホース以外)によって作成されました。
警告 — この国際規格を使用する人は、通常の実験室の慣行に精通している必要があります。この規格は、その使用に関連する安全上の問題があったとしても、そのすべてに対処することを意図していません。適切な安全衛生慣行を確立し、国内の規制条件を確実に遵守することは、ユーザーの責任です。
1 スコープ
この国際規格は、湿気の多い条件下での柔軟な気泡材料の圧縮永久歪みを決定する方法を指定しています。
この方法は、試験片を時間、温度、湿度、および一定の圧縮ひずみという指定された条件下に維持し、指定された回復期間後に試験片の厚さへの影響を決定することから構成されます。
2 規範的参照
次の規範文書には、このテキストで参照することにより、この国際規格の規定を構成する規定が含まれています。日付の記載された参考資料については、これらの刊行物に対するその後の修正または改訂は適用されません。ただし、この国際規格に基づく協定の当事者は、以下に示す規範文書の最新版を適用する可能性を調査することをお勧めします。日付のない参照については、参照されている規範文書の最新版が適用されます。 ISO および IEC のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 1923:1981, セルラー プラスチックおよびゴム — 直線寸法の決定。
3 用語と定義
この国際規格の目的のために、次の用語と定義が適用されます。
3.1
圧縮永久歪み
所定の温度で所定の時間圧縮し、所定の回復時間後の、気泡材料の試験片の初期の厚さと最終の厚さの差。この差を初期の厚さと呼びます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 13362 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses).
WARNING — Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.
1 Scope
This International Standard specifies a method for determining the compression set of flexible cellular materials under humid conditions.
This method consists of maintaining the test piece under specified conditions of time, temperature, humidity and constant compressive strain and determining the effect on the thickness of the test piece after a specified recovery period.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
- ISO 1923:1981, Cellular plastics and rubbers — Determination of linear dimensions.
3 Term and definition
For the purposes of this International Standard, the following term and definition applies.
3.1
compression set
difference between the initial thickness and the final thickness of a test piece of the cellular material after compression for a given time at a given temperature and after a given recovery time, this difference being referred to the initial thickness