この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令のPart 3 に規定されている規則に従って起草されています。
技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に回覧されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
この国際規格の一部の要素が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。
国際規格 ISO 14546 は、技術委員会 ISO/TC 42, Photographyによって作成されました。
序章
この国際規格は、マガジン カセットの内部クリアランスの設計にスプールの寸法を使用してはならないことを (機器設計者の利益のために) 指摘しています。ポイントからポイントへ出荷されるスプールには、この国際規格に示されているものの 3 倍もの横方向の振れがある場合があります。
1 スコープ
この国際規格は、フィルム、リーダー、トレーラーの寸法、該当する場合はミシン目、航空用途で使用される写真フィルムのロールのパッケージ マーキングを指定します。
この国際規格には、適切なサイズのフィルムに対応するスチール製またはアルミニウム製のスプールのサイズと寸法も含まれています。
2 参考文献
次の規範文書には、このテキストで参照することにより、この国際規格の規定を構成する規定が含まれています。日付の記載された参考資料については、これらの刊行物に対するその後の修正または改訂は適用されません。ただし、この国際規格に基づく協定の当事者は、以下に示す規範文書の最新版を適用する可能性を調査することをお勧めします。日付のない参照については、参照されている規範文書の最新版が適用されます。 ISO および IEC のメンバーは、現在有効な国際規格の登録簿を維持しています。
ISO 1:1975, 工業用長さ測定の標準基準温度。
ISO 554:1976, コンディショニングおよび/またはテスト用の標準大気 - 仕様。
3 用語と定義
この国際規格の目的のために、次の用語と定義が適用されます。
3.1
空中映画
空から写真を撮るために設計されたフィルム
3.2
目標寸法
製造プロセスが目標または設計すべき好ましい寸法
3.3
盟主
フィルムのロールの前縁に取り付けられた素材で、画像の記録を意図したものではなく、通常は巻き上げを補助するためのもの
3.4
公称サイズ
製品ラベルやカタログに記載されているサイズ参照
3.5
ミシン目
巻き取りを容易にするために、フィルムの一方または両方の端付近に開けられた、特定の形状および寸法の穴。
3.6
好ましいサイズ
最も頻繁に使用されるユーザーの需要 (ユニット数) と製品の量 (平方メートル) によって決定される業界標準のサイズ
注記 1:新しい機器の設計者は、可能な限り優先サイズを使用することが推奨されます。
3.7
スプライス
2 枚の素材を結合して 1 つのピースを形成する
3.8
スプール
両端にリムまたはエッジがあり、ピンまたはスピンドル用の軸方向の穴があり、その上にフィルムのロールが巻かれている円筒形の装置
3.9
トレーラー
フィルムのロールの後縁に取り付けられた素材で、画像の記録を意図したものではなく、通常は巻き上げを補助するためのもの
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14546 was prepared by Technical Committee ISO/TC 42, Photography.
Introduction
This International Standard points out (for the benefit of equipment designers) that dimensions of spools should not be used for the design of magazine cassette internal clearances. Spools shipped from point to point may have lateral runout as much as three times those indicated in this International Standard.
1 Scope
This International Standard specifies dimensions for films, leaders and trailers, perforations where applicable, and package marking for rolls of photographic film used in aerial applications.
This International Standard also includes the sizes and dimensions of steel or aluminium spools for appropriate sizes of film.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
ISO 1:1975, Standard reference temperature for industrial length measurements.
ISO 554:1976, Standard atmospheres for conditioning and/or testing — Specifications.
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
aerial film
film designed for taking photographs from the air
3.2
aim dimension
preferred dimension at which the manufacturing process should be aimed or designed
3.3
leader
material attached to the leading edge of the roll of film, not intended for recording of images, and usually to assist in winding
3.4
nominal size
size reference that appears on product labels and in catalogues
3.5
perforations
holes of particular shape and dimensions, punched near one or both edges of the film, to assist with winding
3.6
preferred sizes
industry standard sizes, determined by most frequent user demand (number of units) and product volume (square metres)
Note 1 to entry: Designers of new equipment are encouraged to use preferred sizes whenever possible.
3.7
splice
union of two pieces of material, joined to form a single piece
3.8
spool
cylindrical device that has a rim or edge at each end and an axial hole for a pin or spindle, and on which a roll of film is wound
3.9
trailer
material attached to the trailing edge of the roll of film, not intended for recording of images, and usually to assist in winding