※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
適合性評価に関連する ISO 固有の用語や表現の意味の説明、および貿易の技術的障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照してください。 序文 - 補足情報
この文書を担当する委員会は ISO/TC 156, 金属および合金の腐食です。
導入
ステンレス鋼は耐食性の高い材料として一般的に使用されていますが、孔食、隙間腐食、応力腐食割れなどが発生しやすく、その中でも孔食はステンレス鋼で最もよく発生する現象の一つです。ステンレス鋼の耐孔食性を評価するために一般的に使用されるパラメータは、安定した孔食が成長するとみなされない最低電位を定義するいわゆる孔食電位です。孔食は一般に、サイズ、方位、合金成分、不純物、介在物、偏析、表面処理、履歴、経過時間、環境の変動などの不均一性に依存する確率的な性質を示すため、その測定には少なくとも数回の測定が必要です。価値観。
1 スコープ
この国際規格は、ステンレス鋼 (オーステナイト系、フェライト系/オーステナイト系、フェライト系、マルテンサイト系ステンレス鋼) の孔食電位を電位制御下で決定する手順について説明しています。
他の定電位試験法[ 1][2] と比較した主な利点は、この試験法の迅速性であり、1 回の電位スキャンで孔食電位を測定できます。
この国際規格によって決定される孔食の可能性は、性能の相対的な指標として使用できます。たとえば、さまざまなロットのステンレス鋼グレードおよび製品の相対的な性能を比較できます。この国際規格に記載されている試験は、実際の使用条件下で実際の孔食が発生する可能性があるかどうかを判断することを目的としたものではありません。
参考文献
| 1 | ISO 17475, 金属および合金の腐食 - 電気化学的試験方法 - 定電位分極および動電位分極測定を実施するためのガイドライン |
| 2 | ISO 17864, 金属および合金の腐食 - 定電位制御下での臨界孔食温度の決定 |
| 3 | JIS G 0577,ステンレス鋼の孔食電位の測定方法 |
| 4 | ISO 17474, 金属および合金の腐食 - 腐食試験における電気化学測定に適用される規約 |
| 5 | ISO 14802, 金属および合金の腐食 — 腐食データの分析に統計を適用するためのガイドライン |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 156, Corrosion of metals and alloys.
Introduction
Although stainless steel is generally used as a corrosion-resistant material, it is susceptible to pitting corrosion, crevice corrosion, stress corrosion cracking, etc. Among those, pitting corrosion is one of the most common phenomena that occur on stainless steels. A commonly used parameter to evaluate the pitting corrosion resistance of stainless steel, is so-called pitting potential that defines the lowest potential below which stables pits are not considered to grow. Since pitting corrosion generally shows a stochastic nature dependent upon inhomogeneity in terms of size, orientation, alloying components, impurity, inclusions, segregation, surface treatment, history, elapsed time, fluctuation of environment, etc., its measurement requires at least a couple of values.
1 Scope
This International Standard describes the procedure for determining the pitting potential for stainless steels (austenitic, ferritic/austenitic, ferritic, martensitic stainless steel) under potentiodynamiccontrol.
The principal advantage compared with other potentiostatic test methods[1][2] is the rapidity of this test method, with which the pitting potential can be measured in a single potential scan.
The pitting potential as determined by this International Standard can be used as a relative index of performance. For example, one can compare the relative performances for different lots of stainless-steel grades and products. The test described in this International Standard is not intended to determine the pitting potential at which actual pitting can occur under real service conditions, or not.
Bibliography
| 1 | ISO 17475, Corrosion of metals and alloys — Electrochemical test methods — Guidelines for conducting potentiostatic and potentiodynamic polarization measurements |
| 2 | ISO 17864, Corrosion of metals and alloys — Determination of the critical pitting temperature under potientiostatic control |
| 3 | JIS G 0577, Method for measuring pitting potential of stainless steels |
| 4 | ISO 17474, Corrosion of metals and alloys — Conventions applicable to electrochemical measurements in corrosion testing |
| 5 | ISO 14802, Corrosion of metals and alloys — Guidelines for applying statistics to analysis of corrosion data |