※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 3 部に規定されている規則に従って草案されています。
技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この国際規格の要素の一部が特許権の対象となる可能性が注目されています。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。
国際規格 ISO 15227 は、技術委員会 ISO/TC 172, 光学および光学機器、分科会 SC 5, 顕微鏡および内視鏡によって作成されました。
1 スコープ
この国際規格は、実体顕微鏡の最小要件を確保するための試験条件と推奨される試験方法を指定しています。これらの最小要件は ISO 10936-1, ISO 11884-1, および ISO 11884-2 で規定されています。
この国際規格で規定されている試験方法が推奨されていますが、同様の結果が得られる場合には他の試験方法の使用も認められます。
2 規範的参照
以下の規範文書には、本文中の参照を通じてこの国際規格の規定を構成する規定が含まれています。日付が古い参照については、これらの出版物に対するその後の修正または改訂は適用されません。ただし、この国際規格に基づく協定の当事者は、以下に示す規範文書の最新版を適用する可能性を調査することが推奨されます。日付のない参照については、参照されている規範文書の最新版が適用されます。 ISO および IEC のメンバーは、現在有効な国際規格の登録簿を維持しています。
ISO 10934-1, 光学および光学機器 — 顕微鏡の語彙 — Part 1: 光学顕微鏡。
ISO/CIE 10526, 測色用の CIE 標準光源。
3 用語と定義
この国際規格の目的には、ISO 10934-1 に示されている用語と定義が適用されます。
参考文献
| 1 | ISO 11884-1, 光学および光学機器 — 実体顕微鏡の最小要件 — Part 1: 一般用途の実体顕微鏡。 |
| 2 | ISO 11884-2, 光学および光学機器 — 実体顕微鏡の最小要件 — Part 2: 高性能顕微鏡。 |
| 3 | ISO 10936-1, 光学および光学機器 - 手術用顕微鏡 - Part 1: 要件とテスト方法。 |
| 4 | ISO 572, 測定方法と結果の精度 (真性と精度) 。 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15227 was prepared by Technical Committee ISO/TC 172, Optics and optical instruments, Subcommittee SC 5, Microscopes and endoscopes.
1 Scope
This International Standard specifies test conditions and recommended test methods to ensure the minimum requirements for stereomicroscopes. These minimum requirements are given in ISO 10936-1, ISO 11884-1 and ISO 11884-2.
The test methods specified in this International Standard are recommended, but use of other test methods is permitted if the same results are obtained.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
ISO 10934-1, Optics and optical instruments — Vocabulary for microscopy — Part 1: Light microscopy.
ISO/CIE 10526, CIE standard illuminants for colorimetry.
3 Terms and definitions
For the purposes of this International Standard, the terms and definitions given in ISO 10934-1 apply.
Bibliography
| 1 | ISO 11884-1, Optics and optical instruments — Minimum requirements for stereomicroscopes — Part 1: Stereomicroscopes for general use. |
| 2 | ISO 11884-2, Optics and optical instruments — Minimum requirements for stereomicroscopes — Part 2: High performance microscopes. |
| 3 | ISO 10936-1, Optics and optical instruments — Operation microscopes — Part 1: Requirements and test methods. |
| 4 | ISO 5725 (all parts), Accuracy (trueness and precision) of measurement methods and results. |