※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 3 部に規定されている規則に従って草案されています。
技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この国際規格の要素の一部が特許権の対象となる可能性が注目されています。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。
国際規格 ISO 15695 は、金属およびその他の無機コーティングに関する ISO/TC 107 技術委員会によって作成されました。
1 スコープ
この国際規格は、エナメル仕上げの耐傷性を決定するための試験方法を指定しています。この方法は ISO 1518:1992 「塗料およびワニス - スクラッチ テスト」に基づいていますが、かなり高い力で実行されます。
得られる耐傷性の値は、強い力の下で鋭利な物体によって引っ掻かれたときのホーロー仕上げの耐久性の尺度です。この値は、EN 101:1991 「セラミックタイル - モースによる表面の引っかき硬度の決定」に記載されている手順によって測定される量である引っかき硬度と混同しないでください。
2 規範的参照
以下の規範文書には、本文中の参照を通じてこの国際規格の規定を構成する規定が含まれています。日付が古い参照については、これらの出版物に対するその後の修正または改訂は適用されません。ただし、この国際規格に基づく協定の当事者は、以下に示す規範文書の最新版を適用する可能性を調査することが推奨されます。日付のない参照については、参照されている規範文書の最新版が適用されます。 ISO および IEC のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 2723:1995, 鋼板用ガラス質および磁器エナメル - 試験用の試験片の製造。
- ISO 2724:1973, 鋳鉄用ガラス質および磁器エナメル - 試験用の試験片の製造。
- ISO 7724-3:— 1) 、塗料およびワニス — 測色 — Part 3: CIELAB による色差の計算。
- ISO 13804:1999, アルミニウム用ガラス質およびホーロー - 試験用の試験片の製造。
3 用語と定義
この国際規格の目的のために、次の用語と定義が適用されます。
3.1
耐傷性
テストされた長さの 50% 未満にわたって、各色 (赤、緑、青、黒) のフェルト ペンの色がスクラッチに保持される最大の力 (ニュートン)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15695 was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings.
1 Scope
This International Standard specifies a test method for the determination of the scratch resistance of enamel finishes. The method is based on ISO 1518:1992, Paints and varnishes — Scratch test, but is performed at significantly higher forces.
The value of the scratch resistance that is obtained is a measure of the durability of porcelain enamel finishes when scratched by sharp objects under high forces. The value should not be confused with scratch hardness, a quantity that is measured by the procedure described in EN 101:1991, Ceramic tiles — Determination of scratch hardness of surface according to Mohs.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
- ISO 2723:1995, Vitreous and porcelain enamels for sheet steel — Production of specimens for testing.
- ISO 2724:1973, Vitreous and porcelain enamels for cast iron — Production of specimens for testing.
- ISO 7724-3:—1), Paints and varnishes — Colorimetry — Part 3: Calculation of colour differences by CIELAB.
- ISO 13804:1999, Vitreous and porcelain enamels for aluminium — Production of specimens for testing.
3 Terms and definitions
For the purposes of this International Standard, the following term and definition apply.
3.1
scratch resistance
highest force, in newtons, at which the scratch retains the colour of the felt pen for each individual colour (red, green, blue and black) over less than 50 % of the tested length