※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
適合性評価に関連する ISO 固有の用語や表現の意味の説明、および貿易の技術的障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照してください。 序文 - 補足情報
この文書を担当する委員会は ISO/TC 206, ファインセラミックスです。
1 スコープ
この国際規格には手順が記載されています
- 引張または圧縮で均一に負荷がかかった基準試験片を使用して、試験機の荷重列のミスアライメントの程度を検証する。
- ねじれや曲がりなどの不具合を修正するための指示を出します。
この国際規格は、繊維強化材を含むセラミックマトリックス複合材料の試験前に、定量的かつ許容可能な制限を提供することを目的としたものではありません。一方向 (1D)、二方向 (2D)、および三方向 ( x D, 2 < x ≤ 3) に沿って荷重を加えたものです。補強の 1 つの主軸。この制限は、各タイプの複合材料の位置ずれ欠陥に対する感度によって異なります。
注 1この制限は、試験機関と顧客の間で定義されます。
注 2モノリシック セラミックは位置ずれ欠陥に非常に敏感ですが、CMC (セラミック マトリックス複合材料) は一般に位置ずれ欠陥に中程度敏感です。
2 規範的参照
以下の文書は、全部または一部がこの文書で規範的に参照されており、その適用には不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 3611, 幾何製品仕様 (GPS) — 寸法測定装置: 外部測定用マイクロメーター — 設計および計測特性
- ISO 7500-1, 金属材料 — 静的一軸試験機の検証 — Part 1: 引張/圧縮試験機 — 力測定システムの検証と校正
- ISO/IEC 17025, 試験および校正機関の能力に関する一般要件
- CEN/TR 13233:2007, アドバンストテクニカルセラミックス — 表記と記号(将来の ISO NP 19634 に置き換えられる予定)
3 用語と定義
この文書の目的上、CEN/TR 13233:2007 (将来の ISO NP 19634 に置き換えられる) および以下の用語と定義が適用されます。
3.1 一般
3.1.1
校正された長さ
l
均一かつ最小の断面積を持つ基準試験片の一部
3.1.2
幅
b
校正された長さにおける基準試験片の幅
3.1.3
厚さ.厚さ
h
校正された長さにおける基準試験片の厚さ
3.2 欠陥のType
3.2.1
C型マグニチュード
θ
2 つのグリップそれぞれの荷重軸間の角度
注記 1: 図 1 を参照。
3.2.2
S 型マグニチュード
d
荷重軸が平行な場合の荷重軸間の距離
注記 1: 図 2 を参照。
3.2.3
ねじり欠陥の大きさ
ϕ
グリップ面間の角度
注記 1: 図 3 を参照。
参考文献
| 1 | 一軸荷重をかけた引張圧縮試験片の位置ずれによる曲げの測定に関する実践規範。 J. Bressers 編集者、欧州委員会報告書番号 EUR 16138 EN, ISBN 92-826-9681-2 |
| 2 | Reynaud P.、Tallaron C.、Cosculluela A.、Cambas C.、Gomez P.、Delamaide JL et al.、ICCM 12, Juillet, 1999, 引張圧縮で一軸荷重をかけた CMC 試験片の曲げの測定、パリ |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 206, Fine ceramics.
1 Scope
This International Standard describes a procedure
- to verify the degree of misalignment of the load train of the test machines using a reference test specimen uniformly loaded in tension or in compression, and
- to give indications in order to correct defects such as torsion and bending.
This International Standard is not intended to provide a quantitative and acceptable limit before the testing of ceramic matrix composites with a fibre reinforcement: unidirectional (1D), bidirectional (2D), and tridirectional (xD, with 2 < x ≤ 3) loaded along one principal axis of reinforcement. This limit depends on the sensitivity of each type of composite to the misalignment defect.
NOTE 1 This limit is to be defined between the testing establishment and the customer.
NOTE 2 Monolithic ceramics are very sensitive to misalignment defects while CMCs (ceramic matrix composite) in general are moderately sensitive to them.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 3611, Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
- ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system
- ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
- CEN/TR 13233:2007, Advanced technical ceramics — Notations and symbols (to be replaced by future ISO NP 19634)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in CEN/TR 13233:2007 (to be replaced by future ISO NP 19634) and the following apply.
3.1 General
3.1.1
calibrated length
l
part of the reference test specimen which has a uniform and minimum cross-section area
3.1.2
width
b
width of the reference test specimen in the calibrated length
3.1.3
thickness
h
thickness of the reference test specimen in the calibrated length
3.2 Type of defects
3.2.1
C-type magnitude
θ
angle between the loading axis of each of the two grips
Note 1 to entry: See Figure 1.
3.2.2
S-type magnitude
d
distance between the loading axis when they are parallel
Note 1 to entry: See Figure 2.
3.2.3
torsion defect magnitude
ϕ
angle between the gripping planes
Note 1 to entry: See Figure 3.
Bibliography
| 1 | A code of practice for the measurement of misalignment induced bending in uniaxially loaded tension-compression test pieces; J. Bressers Editor, European Commission report no. EUR 16138 EN, ISBN 92-826-9681-2 |
| 2 | Reynaud P., Tallaron C., Cosculluela A., Cambas C., Gomez P., Delamaide J.L. et al., ICCM 12, Juillet, 1999, Measurement of bending in specimens of CMC uniaxially loaded in tension-compression, Paris |