この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令のPart 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令のPart 2 の編集規則に従って起草されました ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
適合性評価に関連する ISO 固有の用語および表現の意味に関する説明、および技術的貿易障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照して ください 。
この文書を担当する委員会は、ISO/TC 238, 固体バイオ燃料です。
序章
長さと直径が仕様外のペレットは、スクリュー コンベア、サイロ アウトレット、およびバーナー供給システムでの輸送に問題を引き起こす可能性があります。 ISO 17225-1, ISO 17225-2, ISO 17225-6, および ISO 17225-8 では、ペレットの寸法が規定されています。この国際規格では、ISO 17225-2 に従って直径の分類を決定する手順と、ペレットの長さと直径について説明しています。
1 スコープ
この国際規格は、ペレットの直径と長さを決定する方法を規定しています。ペレットの長さに関しては、特大ペレットの割合の決定と平均長の決定の両方の方法が含まれています。
2 参考文献
以下の文書の全体または一部は、この文書で規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 16559, 固体バイオ燃料 — 用語、定義および説明
- ISO 17225-1, 固体バイオ燃料 — 燃料の仕様とクラス — Part 1: 一般要件
- ISO 17225-2, 固体バイオ燃料 — 燃料の仕様とクラス — Part 2: 傾斜木質ペレット
- ISO 17225-6, 固体バイオ燃料 — 燃料の仕様とクラス — Part 6: 傾斜非木質ペレット
- ISO 17225-8 1 、固体バイオ燃料 — 燃料の仕様およびクラス — Part 8: 熱処理および高密度化されたバイオマス燃料
- EN 14778:2011, 固体バイオ燃料 — サンプリング
- EN 14780:2011, 固体バイオ燃料 — サンプル前処理
- ISO 18846-2 、固体バイオ燃料 - ペレット量での微粉含有量の決定
- ISO 3310-2, 試験用ふるい — 技術的要件と試験 — Part 2: 穴あき金属板の試験用ふるい
3 用語と定義
このドキュメントの目的のために、ISO 16559 で指定されている次の用語と定義が適用されます。
3.1
テストサンプル
分析のために研究所に送られた元のサンプル
3.2
テスト部分
試験サンプルから抽出され、分析中に使用されるサンプル。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 238, Solid biofuels.
Introduction
Pellets with a length and diameter outside the specification can cause problems with transportation in screw conveyors, silo outlets, and burner feeding systems. ISO 17225-1, ISO 17225-2, ISO 17225-6, and ISO 17225-8 stipulate dimensions of pellets. This International Standard describes procedures for determination the diameter classification according to ISO 17225-2 as well as the length and diameter of pellets.
1 Scope
This International Standard specifies the methods for the determination of diameter and length of pellets. Concerning the pellet length methods for both determination of the proportion of oversized pellets and for determination of the average length are included.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 16559, Solid biofuels — Terminology, definitions and descriptions
- ISO 17225-1, Solid biofuels — Fuel specifications and classes — Part 1: General requirements
- ISO 17225-2, Solid biofuels — Fuel specifications and classes — Part 2: Graded wood pellets
- ISO 17225-6, Solid biofuels — Fuel specifications and classes — Part 6: Graded non-woody pellets
- ISO 17225-8 1 , Solid biofuels — Fuel specifications and classes — Part 8: Thermally treated and densified biomass fuels
- EN 14778:2011, Solid biofuels — Sampling
- EN 14780:2011, Solid biofuels — Sample preparation
- ISO 18846 2 , Solid Biofuels — Determination of fines content in quantities of pellets
- ISO 3310-2, Test sieves — Technical requirements and testing — Part 2: Test sieves of perforated metal plate
3 Terms and definitions
For the purpose of this document, the following terms and definitions given in ISO 16559 apply
3.1
test sample
original sample sent to the laboratory for analysis
3.2
test portion
sample extracted from the test sample and used during the analysis