※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part 1 部に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を 参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易の技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、 www を参照してください。 .iso.org/iso/foreword.html
この文書は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 2, 試験および分析によって作成されました。
この第 5 版は、技術的に改訂された第 4 版 (ISO 2007:2007) を廃止し、置き換えます。
前版との主な変更点は以下の通りです。
- 5.1 および 5.2 に平行平板プラスチメータとパンチの概略図を含める。
- 第 5 条に加熱装置と温度制御システムを含める。
- 第 5 条にタバコ紙を含める。
- 第6項の試験片厚さの変更。
- 第 7 条の校正要件の変更。
警告 1この文書を使用する人は、通常の実験室での実践に精通している必要があります。この文書は、その使用に関連する安全上の問題がある場合、そのすべてに対処することを目的とするものではありません。適切な安全衛生慣行を確立し、その他の制限の適用を判断するのはユーザーの責任です。
警告 2この文書で指定されている特定の手順には、局所的な環境危険を引き起こす可能性のある物質の使用または生成、または廃棄物の生成が含まれる場合があります。使用後の安全な取り扱いと廃棄については、適切な文書を参照する必要があります。
1 スコープ
この文書は、生ゴムおよび未加硫配合ゴムの可塑性を迅速に測定する方法を規定しています。 ISO 2930 に規定されている可塑性保持指数 (PRI) の決定に適用できます。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
この文書の目的上、次の用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
可塑性数値
指定された圧縮力、時間、温度の条件下で変形を受けた後の試験片の高さに基づく塑性の尺度
参考文献
| 1 | ISO 2930, ゴム、天然原料 — 可塑性保持指数 (PRI) の決定 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis.
This fifth edition cancels and replaces the fourth edition (ISO 2007:2007), which has been technically revised.
The main changes compared to the previous edition are as follows:
- inclusion of the schematic diagram for the parallel-plate plastimeter and punch in 5.1 and 5.2;
- inclusion of heating device and temperature control system in Clause 5;
- inclusion of cigarette paper in Clause 5;
- change of test piece thickness in Clause 6;
- change of calibration requirement in Clause 7.
WARNING 1 Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to determine applicability of any other restrictions.
WARNING 2 Certain procedures specified in this document might involve the use or generation of substances, or the generation of waste, that could constitute a local environmental hazard. Reference should be made to appropriate documentation on safe handling and disposal after use.
1 Scope
This document specifies a method for the rapid determination of the plasticity of raw rubber and unvulcanized compounded rubber. It is applicable to the determination of the plasticity retention index (PRI) as specified in ISO 2930.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 1795, Rubber, raw natural and raw synthetic — Sampling and further preparative procedures
- ISO 18899, Rubber — Guide to the calibration of test equipment
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1
plasticity number
measure of plasticity, based upon the height of a test piece after being subjected to deformation under specified conditions of compressive force, time and temperature
Bibliography
| 1 | ISO 2930, Rubber, raw natural — Determination of plasticity retention index (PRI) |