※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 2 部に規定されている規則に従って草案されています。
技術委員会の主な任務は、国際規格を作成することです。技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。
ISO 20081 は、技術委員会 ISO/TC 18 「亜鉛および亜鉛合金」 、小委員会 SC 1 「亜鉛および亜鉛合金のサンプリングおよび分析方法」によって作成されました。
この第 1 版は、技術的に改訂された ISO 3751:1976, ISO 3752:1976, ISO 3816:1976, および ISO 3817:1976 を取り消し、置き換えます。
1 スコープ
この国際規格は、ISO 752 および ISO 301 で指定されている、分析用の亜鉛および亜鉛合金のサンプリング要件を指定します。
2 規範的参照
この文書を適用するためには、以下の参照文書が不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
この文書の目的のために、ISO 301 および ISO 752 で与えられる用語と定義および以下が適用されます。
3.1
サンプル
製品の一部、その化学組成を表すもの
3.2
試験片
分析のために提出された材料の最終形態
3.3
鋳造品の委託販売
荷物として受け取った材料
注記 1:この定義は、サンプリングの目的で購入者と供給者の間で別段の合意がない限り使用されます。
3.4
サンプリングユニット
委託品の中から選んだ個別のキャスト製品
3.5
大きなサンプル
委託品から選択されたサンプリングユニットの合計量
3.6
テストサンプル
大量のサンプルから調製され、そこから試験部分が採取されるサンプル
3.7
テスト部分
試験サンプルから採取され、実際に分析が実行される物質の量
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 20081 was prepared by Technical Committee ISO/TC 18, Zinc and zinc alloys, Subcommittee SC 1, Methods of sampling and analysis of zinc and zinc alloys.
This first edition cancels and replaces ISO 3751:1976, ISO 3752:1976, ISO 3816:1976 and ISO 3817:1976, which have been technically revised.
1 Scope
This International Standard specifies the requirements for sampling of zinc and zinc alloys, as specified in ISO 752 and ISO 301, for analysis.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 301, Zinc alloy ingots intended for casting
- ISO 752, Zinc ingots
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 301 and ISO 752 and the following apply.
3.1
sample
portion of the product, representative of its chemical composition
3.2
test piece
final form of the material submitted for analysis
3.3
consignment of cast product
material received as load
Note 1 to entry: This definition is used unless otherwise agreed between the purchaser and the supplier for the purpose of sampling.
3.4
sampling unit
individual cast product selected from a consignment
3.5
gross sample
total amount of sampling units selected from a consignment
3.6
test sample
sample prepared from the gross sample and from which test portions are taken
3.7
test portions
quantity of material taken from the test sample and on which the analysis is actually carried out