※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の開発に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2 ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自主的な性質に関する説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、次を参照してください。次の URL: www.iso.org/iso/foreword.html
この文書は、専門委員会 ISO/TC 206, ファイン セラミックスによって作成されました。
1 スコープ
このドキュメントでは、室温で一定の振幅で負荷をかけたセラミック - セラミック、セラミック - 金属、およびセラミック - ガラス接合の界面引張/引張またはせん断/せん断繰り返し疲労特性を決定するための試験方法を指定します。試験片の準備手順、試験モードと速度 (負荷速度または変位)、データ収集とレポートの手順が記載されています。
このドキュメントは主に、モノリシック ファイン セラミックスおよびウィスカー、繊維、または粒子で強化されたセラミック複合材を含むセラミック材料に適用されます。この試験方法は、材料研究、品質管理、特性評価、および設計データ生成の目的で使用できます。
2 参考文献
以下のドキュメントは、その内容の一部またはすべてがこのドキュメントの要件を構成するように、本文で参照されています。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 3611, 幾何学的製品仕様 (GPS) - 寸法測定装置: 外部測定用マイクロメータ - 設計および計測特性
- ISO 7500-1, 金属材料 — 静的一軸試験機の校正と検証 — 1: 引張/圧縮試験機 — 力測定システムの校正と検証
- ISO 13124, ファイン セラミックス (アドバンスド セラミックス、アドバンスド テクニカル セラミックス) — セラミック材料の界面結合強度の試験方法
3 用語と定義
このドキュメントでは、次の用語と定義が適用されます。
ISO と IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
3.1
クロスボンド試験片
対称十字形の試験サンプル
注記 1 ISO 13124 に記載されているように、同じ形状とサイズの 2 つの長方形のバーを結合して作成します。
3.2
繰り返し疲労時の平均適用応力
σmm
繰返し疲労時の最大負荷応力と最小負荷応力の平均値
3.3
定振幅負荷
与えられた平均適用応力σmの下で、繰り返し疲労荷重における波形荷重のピーク荷重と谷荷重を一定に保つ Δ σ = ( σmax − σmin )/2 = σmax − σm = σm − σmin
3.4
サイクル数
N
試験中に試験片に加えられた負荷サイクルの総数
3.5
繰返し疲労寿命
Nf
試験片が破損するまでの総負荷サイクル数
3.6
失敗するまでの時間
tf
試験片が破損するまでの時間
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 206, Fine ceramics.
1 Scope
This document specifies a test method for determining interfacial tensile/tensile or shear/shear cyclic fatigue properties of ceramic-ceramic, ceramic-metal, and ceramic-glass joining loaded in the constant amplitude at room temperature. Procedures for test piece preparation, test modes and rates (load rate or displacement), data collection and reporting procedures are given.
This document applies primarily to ceramic materials, including monolithic fine ceramics and whisker-, fibre- or particle-reinforced ceramic composites. This test method can be used for material research, quality control, and characterization and design data-generation purposes.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 3611, Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
- ISO 7500-1, Metallic materials — Calibration and verification of static uniaxial testing machines — 1: Tension/compression testing machines — Calibration and verification of the force-measuring system
- ISO 13124, Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for interfacial bond strength of ceramic materials
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1
cross-bonded test piece
test sample in the form of a symmetrical cross
Note 1 to entry: Prepared by joining two rectangular bars with the same shape and size, as described in ISO 13124.
3.2
average applied stress during cyclic fatigue
σm
average value between the maximum applied stress and the minimum applied stress during cyclic fatigue
3.3
constant amplitude loading
under a given average applied stress, σm, keeping peak loads and valley loads constant for wave form loading in cyclic fatigue loading, Δσ = (σmax − σmin)/2 = σmax − σm = σm − σmin
3.4
number of cycles
N
total number of loading cycles applied to the test piece during the test
3.5
cyclic fatigue life
Nf
total number of loading cycles until the test piece is up to failure
3.6
time to failure
tf
time duration until the test piece is up to failure