この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令第 1 Part に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易の技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html
この文書は、技術委員会 ISO/TC 35, 塗料およびワニス、小委員会 SC 9, 塗料およびワニスの一般試験方法によって作成されました。
導入
コーティングを塗布する場合、生成される液滴のサイズまたはサイズ分布は塗布結果にとって非常に重要です。スプレーエネルギーやコーティング材料の流速などの塗布パラメータ、および溶媒組成やレオロジー流動性能などの技術的特性を変更することにより、塗布結果の品質を制御できます。また、塗布時の気候条件 (温度、相対湿度、空気の落下速度など) も結果に大きく影響します。塗布後、または中間乾燥または最終乾燥後に不揮発性物質を測定することにより、湿式または乾式塗布の結果を特徴付けることができ、その結果、塗布中に生成された液滴サイズ分布と溶剤放出を間接的に参照することができます。計算された揮発分により、追加のコーティングを塗布する前に、それぞれのコーティングの十分な中間乾燥が決定されます。
1 スコープ
この文書は、塗布直後、または中間または最終乾燥後のコーティングの不揮発分を測定するための試験方法を規定しています。実際には、揮発性物質の測定は、特に追加のコーティング材料で再コーティングされる水で希釈可能なコーティングに関して適用されます。
さらに、この方法を使用して、さまざまな塗布および乾燥方法の効率を比較することもできます。
塗布後の製品の不揮発性または揮発性物質の含有量は絶対的な変数ではなく、塗布および試験中に適用される乾燥条件によって異なります。したがって、この方法を適用すると、溶媒の保持、熱分解、低分子量の蒸発により、不揮発分の含有量は相対値のみが得られ、実際の値は得られません。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
この文書の目的のために、ISO 4618 および以下に示されている用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
プロセスステップ
所定のコーティングシステムを得るには、コーティング方法に関して連続する必要がある操作と期間。
注記 1:焦点に応じて、いくつかの連続した操作を 1 つのプロセスステップとして含めることができます。
3.2
定義されたプロセスステップ後の不揮発性物質
nv P
指定された試験条件下での試験の単一プロセスステップから適用後に得られる質量による残留物
3.3
揮発性物質
VM
指定された試験条件下での蒸発によって得られる質量損失
3.4
定義されたプロセスステップ後の揮発性物質
P
指定された試験条件下での試験の単一プロセスステップから適用後に得られる質量損失
参考文献
| 1 | ISO 5725-2, 測定方法と結果の精度 (真性と精度) — Part 2: 標準測定方法の再現性と再現性を決定するための基本方法 |
| 2 | ISO/TR 22971, 測定方法と結果の精度 (真性と精度) — 研究室間の再現性と再現性の結果を設計、実装、統計的に分析する際に ISO 5725-2:1994 を使用するための実践的なガイダンス |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9, General test methods for paints and varnishes.
Introduction
When applying coatings, the size or the size distribution of the generated drops is of great importance for the application result. By varying the application parameters, such as spraying energy and the rate of flow of the coating material as well as the technical properties such as solvent composition and rheological flow performance, the quality of the application result can be controlled. Also, climatic conditions during the application (e.g. temperature, relative humidity, and air falling speed) highly influence the result. By determining the non-volatile matter after application or after intermediate or final drying, it is possible to characterize the wet or dry application result and, consequently, to indirectly refer to the generated drop size distribution and the solvent emission during the application. By means of the calculated volatile matter, the sufficient intermediate drying of the respective coating is determined before applying an additional coating.
1 Scope
This document specifies a test method for the determination of non-volatile matter of coatings directly after application or after intermediate or final drying. In practice, the determination of volatile matter is applied particularly in regard to water-thinnable coatings which are re-coated with an additional coating material.
Furthermore, the method can be used to compare the efficiency of different application and drying methods.
The content of non-volatile or volatile matter of a product after application is no absolute variable but depends on the application and drying conditions applied during the test. Consequently, applying this method gives only relative values and not the real values for the content of non-volatile matter, due to solvent retention, thermal decomposition and evaporation of low-molecular contents.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 1513, Paints and varnishes — Examination and preparation of test samples
- ISO 1514, Paints and varnishes — Standard panels for testing
- ISO 4618, Paints and varnishes — Terms and definitions
- ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4618 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1
process step
operations and time periods, which have to be successive in regard to the coating method in order to result in a given coating system.
Note 1 to entry: Depending on the focus several successive operations can be subsumed as one process step.
3.2
non-volatile matter after defined process step
nvP
residue by mass obtained after the application from the single process steps of examination under specified conditions of test
3.3
volatile matter
VM
loss by mass obtained by evaporation under specified conditions of test
3.4
volatile matter after defined process step
VMP
loss by mass obtained after the application from the single process steps of examination under specified conditions of test
Bibliography
| 1 | ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| 2 | ISO/TR 22971, Accuracy (trueness and precision) of measurement methods and results — Practical guidance for the use of ISO 5725-2:1994 in designing, implementing and statistically analysing interlaboratory repeatability and reproducibility results |