※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令第 1 Part に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易の技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、 www を 参照してください。 .iso.org/iso/foreword.html
この文書は、技術委員会 ISO/TC 61, プラスチック、小委員会 SC 11, 製品によって作成されました。
安全上の注意この文書を使用する人は、該当する場合、通常の実験室の業務に精通している必要があります。この文書は、その使用に関連する安全上の問題がある場合、そのすべてに対処することを目的とするものではありません。適切な安全と健康慣行を確立するのはユーザーの責任です。
環境に関する声明この文書で許可されている内容の一部は、環境に悪影響を与える可能性があることを理解されています。技術的な利点により、これらの材料の許容可能な代替品が得られるため、可能な限りこの文書から除外されます。テスト終了後、この文書の使用者は廃棄物の適切な処分を行うよう注意することが重要です。
1 スコープ
この文書は、剥離力下で特定の基材に接着された弾性または織物の床材または壁材の接着力を測定する試験方法を指定しています。 「壁紙」という用語には、いかなる種類の壁紙も含まれません。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
この文書の目的のために、ISO 472 および以下に示されている用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
カバーリング
柔軟な弾性または織物の床材または壁材
3.2
カバー用接着剤
カバー (3.1) とさまざまな基材の間にしっかりとした耐久性のある接着を生成することを目的とした接着剤
参考文献
| 1 | ISO 3205 1 、推奨試験温度 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
SAFETY PRECAUTIONS Persons using this document should be familiar with the normal laboratory practice, if applicable. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices.
ENVIRONMENTAL STATEMENT It is understood that some of the material permitted in this document may have negative environmental impact. As technological advantages lead to acceptable alternatives for these materials, they will be eliminated from this document to the extent possible. At the end of the test, it is essential that the user of this document take care to carry out an appropriate disposal of the wastes.
1 Scope
This document specifies a test method to measure the adhesion of a resilient or textile floor covering or wall covering bonded to a given substrate under peel forces. The term “wall covering” does not include any type of wallpaper.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 472, Plastics — Vocabulary
- ISO 554, Standard atmospheres for conditioning and/or testing — Specifications
- ISO 7500-1, Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Calibration and verification of the force-measuring system
- ISO 9142, Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bonded joints
- ISO 10365, Adhesives — Designation of main failure patterns
- ISO 15605, Adhesives — Sampling
- EN 1067, Adhesives — Examination and preparation of samples for testing
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1
covering
flexible resilient or textile floor covering or wall covering
3.2
adhesive for coverings
adhesive which is intended to produce firm and durable bonds between coverings (3.1) and various substrates
Bibliography
| 1 | ISO 3205 1 , Preferred test temperatures |