※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令のPart 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令のPart 2 の編集規則に従って起草されました ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
適合性評価に関連する ISO 固有の用語および表現の意味に関する説明、および技術的貿易障壁 (TBT) における ISO の WTO 原則への準拠に関する情報については、次の URL を参照してください: 序文 — 補足情報 .
この文書を担当する委員会は、ISO/TC 219, 床材です。
この第 2 版は、技術的に改訂された第 1 版 (ISO 24338:2006) を取り消して置き換えるものです。
1 スコープ
この国際規格は、ラミネート フロア カバー要素の摩耗を測定するための 2 つの方法 (A および B) を指定します。記載されている試験は、表面層が磨耗に抵抗する能力を測定します。
方法 A による摩耗は、指定された研磨紙で覆われた 1 組の荷重を加えた円筒形ホイールに接触させた試験片を回転させることによって達成されます。方法 B による耐摩耗性は、2 つのロードされたホイールを使用して特定の研磨剤を適用して試験片の面を研磨することによって評価されます。定義された程度の摩耗を引き起こすために必要な試験片の回転数は、両方の方法で測定されます。
注記メソッドの精度は不明です。研究所間のデータが利用可能になると、精度ステートメントが追加されます。
2 参考文献
以下のドキュメントの全体または一部は、このドキュメントで規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 48, ゴム、加硫または熱可塑性 — 硬度の測定 (10 IRHD と 100 IRHD の間の硬度)
- ISO 868, プラスチックおよびエボナイト — デュロメーターによる押し込み硬度の測定 (ショア硬度)
- ISO 6506-1, 金属材料 — ブリネル硬さ試験 — Part 1: 試験方法
- ISO 7267-2, ゴムで覆われたローラー — 見かけの硬さの測定 — Part 2: ショア型デュロメーター法
- ASTM D785, プラスチックおよび電気絶縁材料のロックウェル硬さの標準試験方法
参考文献
| [1] | ISO 4545-4, 金属材料 — ヌープ硬度試験 — Part 4: 硬度値の表 |
| [2] | FEPA 規格 42-D, 結合研磨剤および一般産業用途向けの溶融酸化アルミニウム、炭化ケイ素およびその他の研磨材の粒子 |
| [3] | FEPA 標準 44-D, 溶融酸化アルミニウム、炭化ケイ素、その他の研磨材の粒子。かさ密度の測定 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword — Supplementary information .
The committee responsible for this document is ISO/TC 219, Floor coverings.
This second edition cancels and replaces the first edition (ISO 24338:2006) of which has been technically revised.
1 Scope
This International Standard specifies two methods (A and B) for measuring abrasion of laminate floor covering elements. The tests described measure the ability of the surface layer to resist abrasive wear-through.
Abrasion, according to method A, is achieved by rotating a test specimen in contact with a pair of loaded cylindrical wheels covered with specified abrasive paper. The resistance to wear, according to method B, is evaluated by abrading the face of test pieces with a specified abrasive applied by means of two loaded wheels. The number of revolutions of the test specimen required to cause a defined degree of abrasion is measured by both methods.
NOTE The precision of the methods is not known. When inter-laboratory data become available, a precision statement will be added.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 48, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and 100 IRHD)
- ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
- ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method
- ISO 7267-2, Rubber-covered rollers — Determination of apparent hardness — Part 2: Shore-type durometer method
- ASTM D785, Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
Bibliography
| [1] | ISO 4545-4, Metallic materials — Knoop hardness test — Part 4: Table of hardness values |
| [2] | FEPA standard 42-D, Grains of fused aluminium oxide, silicon carbide and other abrasive materials for bonded abrasives and for general industrial applications |
| [3] | FEPA standard 44-D, Grains of fused aluminium oxide, silicon carbide and other abrasive materials. Determination of bulk density |