※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令のPart 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令のPart 2 の編集規則に従って起草されました ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自発的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html .
この文書は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 4, 製品 (ホース以外) によって作成されました。
この第 4 版は、改訂版 ISO 2440:1997/Amd.1:2010 および ISO 2440:1997/Amd.2:2014 を組み込むためのマイナーな改訂を構成する第 3 版 (ISO 2440:1997) を取り消して置き換えます。
警告このドキュメントを使用する人は、通常の実験室の慣行に精通している必要があります。このドキュメントは、その使用に関連する安全上の問題のすべてに対処することを目的としていません。適切な安全衛生慣行を確立し、その他の制限の適用可能性を判断することは、ユーザーの責任です。
1 スコープ
この文書は、柔軟性と剛性の気泡高分子材料について、湿度による酸化や加水分解などの自然に発生する反応の影響を模倣することを目的とした実験手順を指定しています。対象の物理的特性は、指定された処理の適用の前後で測定されます。
試験条件は、連続気泡ラテックス、連続気泡ポリウレタンフォームと独立気泡ポリウレタンフォームの両方、および独立気泡ポリオレフィンフォームに対してのみ与えられています。必要に応じて、その他の材料の条件を追加します。
材料の物理的特性のいずれかに対するエージング手順の影響を調べることができますが、通常テストされるのは、伸びと引張特性、または圧縮または圧痕硬度特性のいずれかです。
これらのテストは、サービスの動作や光への暴露による老化と必ずしも相関するわけではありません。
必要に応じて、この文書に含まれるエージング条件は、上記のタイプの気泡材料のいずれかを含む複合構造に適用できます。これは、細胞材料と他の基質との間の可能な相互作用の調査に役立ちます。複合構造は、完全な完成品またはそこから切り出された代表的な小さな標本の形をとることができます
2 参考文献
以下のドキュメントは、その内容の一部またはすべてがこのドキュメントの要件を構成するように、本文で参照されています。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 23529, ゴム — 物理的試験方法のための試験片の準備とコンディショニングの一般的な手順
3 用語と定義
このドキュメントには、用語と定義は記載されていません。
ISO と IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (others than hoses).
This fourth edition cancels and replaces the third edition (ISO 2440:1997), of which it constitutes a minor revision to incorporate the Amendments ISO 2440:1997/Amd.1:2010 and ISO 2440:1997/Amd.2:2014.
WARNING Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to determine the applicability of any other restrictions.
1 Scope
This document specifies, for flexible and rigid cellular polymeric materials, laboratory procedures which are intended to imitate the effects of naturally occurring reactions such as oxidation or hydrolysis by humidity. The physical properties of interest are measured before and after the application of the specified treatments.
Test conditions are only given for open cellular latex, both open- and closed-cell polyurethane foams, and closed-cell polyolefin foams. Conditions for other materials will be added as required.
The effect of the ageing procedures on any of the physical properties of the material can be examined, but those normally tested are either the elongation and tensile properties, or the compression or indentation hardness properties.
These tests do not necessarily correlate either with service behaviour or with ageing by exposure to light.
If desired, the ageing conditions contained in this document can be applied to composite structures containing any of the above types of cellular material. This can be helpful in the investigation of possible interactions between cellular materials and other substrates. Composite constructions can be in the form of complete finished products or representative small specimens cut there-from
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses: