※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令第 1 Part に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
適合性評価に関連する ISO 固有の用語や表現の意味の説明、および貿易の技術的障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照してください。 序文 - 補足情報 。
この文書を担当する委員会は、ISO/TC 35, 塗料およびワニス、小委員会 SC 9, 塗料およびワニスの一般試験方法です。
この第 4 版は、技術的に改訂された第 3 版 (ISO 2813:1994) を廃止し、置き換えるものです。また、技術的正誤表 ISO 2813:1994/Cor.1:1997 も組み込まれています。
主な技術的な変更は次のとおりです。
- a)タイトルが変更されました。
- b)範囲が拡張され、金属コーティングの光沢測定が含まれるようになりました。
- c) 「鏡面光沢」という用語は「光沢」に置き換えられました。
- d)光沢値は光沢単位 (GU) で示されます。
- e)考えられるエラーの原因に関する新しい付録 (付録 A) が追加されました。
- f)校正標準に関する新しい付録 (付録 B) が追加されました。
- g)一次参照標準の光沢計算に関する新しい付録 (付録 C) が追加されました。
- h)精度の詳細に関する新しい付録 (付録 D) が追加されました。
- i)精度データは大規模な研究室間テストの結果です。
1 スコープ
この国際規格は、20°、60°、または 85°の 3 つの形状を使用してコーティングの光沢を決定する方法を指定しています。この方法は、平面で不透明な基材上の非テクスチャーコーティングの光沢測定に適しています。
注記上記とは異なる試験片については、光沢度の比較測定が可能です。ただし、得られた光沢値が視覚的な光沢認識に対応しているかどうかは保証されません (付録 A を参照)
2 規範的参照
以下の文書は、全部または一部がこの文書で規範的に参照されており、その適用には不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 1514, 塗料およびワニス — 試験用の標準パネル
- ISO 2808, 塗料およびワニス - 膜厚の決定
- ISO 4618:2014, 塗料およびワニス — 用語と定義
3 用語と定義
この文書の目的のために、ISO 4618 および以下に示されている用語と定義が適用されます。
3.1
光沢のある
光を鏡面反射する能力によって特徴付けられる表面の光学的特性
注記 1:光沢度の例としては、高光沢、光沢、シルク光沢、半光沢、サテン、マット、デッドマットなどがあります。
[出典:ISO 4618:2014, 2.132]
3.2
幾何学
指定された角度と割り当てられた開口部を使用した光沢測定方法の識別
3.3
光沢値
光源と受光器の指定された反射角および指定された開口角における、鏡面方向の波長 587.6 nm における屈折率 1.567 のガラス表面で反射された光束に対する、試料から反射された光束の 100 倍の比。
注記 1:光沢値は光沢単位 (GU) で示されます。光沢値を「反射率」として解釈して表現することは許可されていません。
注記 2:コーティング上で測定された光沢値は、最も近い整数 (小数点以下を除く) に四捨五入して表示されます。
注記 3:光沢スケールを定義するために、587.6 nm の波長で 1.567 の屈折率を持つ研磨された黒色ガラスには、20°、60°、および 85° の形状の値 100 が割り当てられます。
注記 4:波長 546.1 nm (比視感度関数の中心波長) における反射率が 1.567 のガラス表面を使用することができる。
注記 5:光沢値は、サンプルの粗さ、質感、構造などの表面特性に影響されます。
参考文献
| 1 | ISO 5725-2, 測定方法と結果の精度 (真性と精度) — Part 2: 標準測定方法の再現性と再現性を決定するための基本方法 |
| 2 | ISO 7668, アルミニウムおよびその合金の陽極酸化 - 20°、45°、60°、または 85°の角度での陽極酸化コーティングの鏡面反射率と鏡面光沢度の測定 |
| 3 | ISO 8254-1, 紙および板紙 — 鏡面光沢度の測定 — Part 1: 収束ビームによる 75° 光沢度、TAPPI 法 |
| 4 | ISO 8254-2, 紙および板紙 — 鏡面光沢度の測定 — Part 2: 平行ビームによる 75° 光沢度、DIN 法 |
| 5 | ISO/TR 22971, 測定方法と結果の精度 (真性と精度) — 研究室間の再現性と再現性の結果を設計、実装、統計的に分析する際に ISO 5725-2:1994 を使用するための実践的なガイダンス |
| 6 | ISO/IEC Guide 99, 計測学の国際語彙 — 基本概念および一般概念および関連用語 (VIM) |
| 7 | EN 14086, 紙および板紙 — 鏡面光沢度の測定 — 平行ビームによる 45° 光沢度、DIN 法 |
| 8 | DIN 1349-1, 光放射の透過 - 光学的に透明な (非散乱) メディア、数量、記号および単位 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information .
The committee responsible for this document is ISO/TC 35, Paints and varnishes, Subcommittee SC 9, General test methods for paints and varnishes.
This fourth edition cancels and replaces the third edition (ISO 2813:1994), which has been technically revised. It also incorporates the Technical Corrigendum ISO 2813:1994/Cor.1:1997.
The main technical changes are:
- a) the title has been changed;
- b) the scope has been extended to include gloss measurement of metallic coatings;
- c) the term “specular gloss” has been replaced by “gloss”;
- d) the gloss value is indicated in gloss units (GU);
- e) a new annex (Annex A) concerning possible sources of error has been added;
- f) a new annex (Annex B) concerning calibration standards has been added;
- g) a new annex (Annex C) concerning gloss calculation of primary reference standards has been added;
- h) a new annex (Annex D) concerning details on precision has been added;
- i) the precision data are the results of a large interlaboratory test.
1 Scope
This International Standard specifies a method for determining the gloss of coatings using the three geometries of 20°, 60° or 85°. The method is suitable for the gloss measurement of non-textured coatings on plane, opaque substrates.
NOTE On test specimens different from these mentioned above, comparative gloss measurements are possible. However, it is not ensured that the obtained gloss values correspond to the visual gloss perception (see Annex A).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 1514, Paints and varnishes — Standard panels for testing
- ISO 2808, Paints and varnishes — Determination of film thickness
- ISO 4618:2014, Paints and varnishes — Terms and definitions
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4618 and the following apply.
3.1
gloss
optical property of a surface, characterized by its ability to reflect light specularly
Note 1 to entry: Examples of degrees of gloss are high gloss, gloss, silk gloss, semigloss, satin, matt, and dead matt.
[SOURCE:ISO 4618:2014, 2.132]
3.2
geometry
identification of a method of gloss measurement using a specified angle with assigned apertures
3.3
gloss value
ratio multiplied by 100 of the luminous flux reflected from a specimen to that reflected by a glass surface with a refractive index of 1,567 at a wavelength of 587,6 nm in specular direction for a specified reflection angle and specified aperture angles of light source and receptor
Note 1 to entry: The gloss value is indicated in gloss units (GU). It is not permitted to interpret and express gloss values as “% reflection”.
Note 2 to entry: Gloss values measured on coatings are expressed rounded to the nearest integer (without decimals).
Note 3 to entry: To define the gloss scale, polished black glass with a refractive index of 1,567 at a wavelength of 587,6 nm is assigned to the value of 100 for 20°, 60° and 85° geometries.
Note 4 to entry: A glass surface with a reflective index of 1,567 at a wavelength of 546,1 nm (which is the central wavelength of the spectral luminous efficiency function) may be used.
Note 5 to entry: The gloss value is influenced by the surface characteristics, e.g. roughness, texture, structure, of the sample.
Bibliography
| 1 | ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| 2 | ISO 7668, Anodizing of aluminium and its alloys — Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20°, 45°, 60° or 85° |
| 3 | ISO 8254-1, Paper and board — Measurement of specular gloss — Part 1: 75° gloss with a converging beam, TAPPI method |
| 4 | ISO 8254-2, Paper and board — Measurement of specular gloss — Part 2: 75° gloss with a parallel beam, DIN method |
| 5 | ISO/TR 22971, Accuracy (trueness and precision) of measurement methods and results — Practical guidance for the use of ISO 5725-2:1994 in designing, implementing and statistically analysing interlaboratory repeatability and reproducibility results |
| 6 | ISO/IEC Guide 99, International vocabulary of metrology — Basic and general concepts and associated terms (VIM) |
| 7 | EN 14086, Paper and board — Measurement of specular gloss — 45° gloss with a parallel beam, DIN method |
| 8 | DIN 1349-1, Durchgang optischer Strahlung durch Medien — Optisch klare Stoffe, Größen, Formelzeichen und Einheiten (en: Transmisson of optical radiation — Optical clear (nonscattering) media, quantities, symbols and units) |