この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持を意図した手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2 ( www.iso.org/directives を参照)
このドキュメントの一部の要素が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
適合性評価に関連する ISO 固有の用語および表現の意味に関する説明、および技術的貿易障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照してください: 序文 - 補足情報 .
この文書を担当する委員会は、ISO/TC45, ゴムおよびゴム製品、小委員会 SC 2, 試験および分析です。
この第 2 版は、基準の参照を更新し、最新の校正情報への参照を提供するために技術的に改訂された第 1 版 (ISO 289-3:1999) を取り消して置き換えます。
ISO 289 は、次の部分で構成され、一般的なタイトルはゴム、未加硫 - せん断ディスク粘度計を使用した測定:
- Part 1: ムーニー粘度の測定
- Part 2: 加硫前特性の決定
- Part 3: 非着色油展乳化重合 SBR のデルタ ムーニー値の決定
- Part 4: ムーニー応力緩和率の決定
序章
デルタ ムーニー値は、混合、押出、およびカレンダー加工の主要段階におけるゴムの挙動または加工性を予測する手段を提供します。これは通常、無着色の油展エマルジョン スチレン-ブタジエン ゴムに関連していますが、他のタイプの挙動に関する情報を提供するのに役立ちます。ただし、後者の場合、ISO 289 のこの部分で指定されている試験条件は適切ではない可能性があります。
警告ISO 289 のこの部分を使用する人は、通常の実験室の慣行に精通している必要があります。 ISO 289 のこの部分は、その使用に関連する安全上の問題があったとしても、そのすべてに対処することを意図していません。適切な安全衛生慣行を確立し、国内の規制条件を確実に遵守することは、ユーザーの責任です。
1 スコープ
ISO 289 のこのパートでは、無着色の油展乳化重合スチレンブタジエン ゴムのデルタ ムーニー値を決定する方法を指定しています。
2 参考文献
以下のドキュメントの全体または一部は、このドキュメントで規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
このドキュメントでは、次の用語と定義が適用されます。
3.1
デルタムーニーA値
注記ISO 1795 では、「大量の試験サンプル」は「均質化された試験サンプル」と呼ばれています。
3.1.1
A1値
15 分と 1 分で記録された質量のない試験サンプルのムーニー粘度の差、つまり ML(1+15) – ML(1+1)
3.1.2
A2値
7 分と 1 分で記録された質量のない試験サンプルのムーニー粘度の差、つまり ML(1+7) – ML(1+1)
3.1.3
A3値
15 分と 1.5 分で記録された大量の試験サンプルのムーニー粘度の差、すなわち ML(1+15) – ML(1+1,5)
3.2
デルタムーニーB値
ローターを始動した直後の最小ムーニー粘度と、質量のない試験サンプルのその後の最大ムーニー粘度との差
注記 1:値は補完的なものであり、加工が容易なゴムと加工が非常に困難なゴムとを区別するために、任意の組み合わせを使用することができます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information .
The committee responsible for this document is ISO/TC45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis.
This second edition cancels and replaces the first edition (ISO 289-3:1999), which has been technically revised to update normative references and to provide a reference to the latest calibration information.
ISO 289 consists of the following parts, under the general title Rubber, unvulcanized — Determinations using a shearing-disc viscometer:
- Part 1: Determination of Mooney viscosity
- Part 2: Determination of pre-vulcanization characteristics
- Part 3: Determination of the Delta Mooney value for non-pigmented, oil-extended emulsion-polymerized SBR
- Part 4: Determination of the Mooney stress-relaxation rate
Introduction
The Delta Mooney value provides a means of predicting the behaviour or processibility of rubber during the primary stages of mixing, extruding, and calendering. It is usually associated with non-pigmented, oil-extended emulsion styrene-butadiene rubber, but it can be of use in providing information about the behaviour of other types. In the latter case, however, the conditions of test specified in this part of ISO 289 might not be suitable.
WARNING Persons using this part of ISO 289 should be familiar with normal laboratory practice. This part of ISO 289 does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.
1 Scope
This part of ISO 289 specifies a method for determining the Delta Mooney value of non-pigmented, oil-extended emulsion-polymerized styrene-butadiene rubber.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 289-1, Rubber, unvulcanised — Determinations using a shearing-disc viscometer — 1: Determination of Mooney viscosity
- ISO 1795, Rubber, raw natural and raw synthetic — Sampling and further preparative procedures
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
Delta Mooney A values
NOTE A “massed test sample” is referred to as a “homogenized test sample” in ISO 1795. Similarly, an “unmassed test sample” can be described as an “unhomogenized test sample”.
3.1.1
A1 value
difference between the Mooney viscosities of an unmassed test sample recorded at 15 min and 1 min, i.e. ML(1+15) – ML(1+1)
3.1.2
A2 value
difference between the Mooney viscosities of an unmassed test sample recorded at 7 min and 1 min, i.e. ML(1+7) – ML(1+1)
3.1.3
A3 value
difference between the Mooney viscosities of a massed test sample recorded at 15 min and 1,5 min, i.e. ML(1+15) – ML(1+1,5)
3.2
Delta Mooney B value
difference between the minimum Mooney viscosity soon after starting the rotor and the subsequent maximum Mooney viscosity for an unmassed test sample
Note 1 to entry: The values are complementary and any combination may be used to assist in distinguishing those rubbers that are easy to process from those that process with significantly greater difficulty.