この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令のPart 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令のPart 2 の編集規則に従って起草されました ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自主的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html .
この文書は、技術委員会 ISO/TC 4, 転がり軸受、小委員会 SC 5, ニードル、円筒および自動調心ころ軸受によって作成されました。
この第 5 版は、技術的に改訂された第 4 版 (ISO 3245:2015) を取り消して置き換えるものです。
主な変更点は次のとおりです。
- 図 1 a) が更新されました。
- 特性 ΔFws の記号は ΔFwgn に置き換えられました。
- 測定および検証方法に関する附属書 B が追加されました。
序章
このドキュメントは、ISO 14638 のマトリックス モデルで提示されている幾何学的製品仕様システム (GPS システム) で定義されている機械要素の幾何学的規格です。
別段の指示がない限り、ISO 8015 で指定されている ISO/GPS の基本規則がこのドキュメントに適用され、ISO 14253-1 で指定されているデフォルトの決定規則がこのドキュメントに従って作成された仕様に適用されます。
機能要件、測定技術、および測定の不確かさの間の関係は、常に考慮されることを意図しています。測定の不確かさについては、ISO 14253-2 を考慮することを意図しています。
シャフトレースウェイとハウジングボアの公差の推奨値は、付録 A に記載されています。
シェル付きで内輪なしの針状ころ軸受の固有特性の測定と検証のガイドラインは、附属書 B に示されています。
1 スコープ
この文書では、内輪なしのシェル形針状ころ軸受に使用する境界寸法と推奨寸法、および最小面取り寸法の制限を指定しています。この文書では、片側が閉じたベアリングの閉じた端の厚さ寸法も指定しています。
また、この文書では、針状ころのコンプリメント穴径の寸法許容差と絞りカップ幅の許容差を指定しています。
2 参考文献
以下のドキュメントの全体または一部は、このドキュメントで規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 5593, 転がり軸受 - 語彙
- ISO 10579, 幾何学的製品仕様 (GPS) — 寸法と公差 — 非剛性部品
- ISO 14405-1, 幾何学的製品仕様 (GPS) — 寸法公差 — Part 1: 線形サイズ
- ISO/TS 17863, 幾何学的製品仕様 (GPS) — 可動アセンブリの公差
3 用語と定義
このドキュメントの目的のために、ISO 5593, ISO 14405-1, および以下に記載されている用語と定義が適用されます。
ISO および IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
3.1
拘束直径
D 1c
ΔFwgn 特性を評価するために拘束条件で使用されるフィーチャの直径
注記1附属書Bのマスターリングゲージの直径に対応する。
参考文献
| 1 | ISO 286-1, 製品の幾何学的仕様 (GPS) — 線形サイズの公差に関する ISO コード システム — Part 1: 公差、偏差、適合の基礎 |
| 2 | ISO 286-2, 幾何学的製品仕様 (GPS) — 線形サイズの公差に関する ISO コード システム — Part 2: 標準公差クラスと穴とシャフトの限界偏差の表 |
| 3 | ISO 1101, 幾何学的製品仕様 (GPS) — 幾何公差 — 形状、方向、位置、振れの公差 |
| 4 | ISO 1132-1, 転がり軸受 — 公差 — Part 1: 用語と定義 |
| 5 | ISO 1938-1:2015, 幾何学的製品仕様 (GPS) — 寸法測定装置 — Part 1: 線形サイズのプレーン リミット ゲージ |
| 6 | ISO 8015, 幾何学的製品仕様 (GPS) — 基礎 — 概念、原則、および規則 |
| 7 | ISO 14253-1, 幾何学的製品仕様 (GPS) — ワークピースおよび測定機器の測定による検査 — Part 1: 仕様への適合または不適合を検証するための決定規則 |
| 8 | ISO 14253-2, 幾何学的製品仕様 (GPS) — ワークピースおよび測定機器の測定による検査 — Part 2: GPS 測定、測定機器の校正、および製品検証における不確かさの推定に関するガイダンス |
| 9 | ISO 14638, 幾何学的製品仕様 (GPS) — マトリックス モデル |
| 10 | ISO 15241, 転がり軸受 — 物理量の記号 |
| 11 | ISO 18203:2016, スチール — 表面硬化層の厚さの決定 |
| 12 | ISO 22872-1 、転がり軸受 — 製品の幾何学的仕様 (GPS) — GPS に関連する記号、用語、および定義 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee SC 5, Needle, cylindrical and spherical roller bearings.
This fifth edition cancels and replaces the fourth edition (ISO 3245:2015), which has been technically revised.
The main changes are as follows:
- Figure 1 a) has been updated;
- the symbol for characteristic ΔFws has been replaced with ΔFwgn;
- Annex B on measuring and verification methods has been added.
Introduction
This document is a machine element geometry standard as defined in the geometrical product specification system (GPS system) as presented in matrix model of ISO 14638.
The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document, unless otherwise indicated.
The connection between functional requirements, measuring technique and measuring uncertainty is always intended to be considered. For measurement uncertainty, it is intended that ISO 14253-2 be considered.
Recommended values for the tolerances for shaft raceway and housing bore are given in Annex A.
Guidelines for measurement and verification of the specific characteristic of needle roller bearings with drawn cup and without inner ring are given in Annex B.
1 Scope
This document specifies the boundary dimensions and preferred dimensions to be used for drawn cup needle roller bearings without inner ring as well as the minimum chamfer dimension limits. This document also specifies the closed end thickness dimensions for bearings with one closed end.
In addition, this document specifies dimensional tolerances for the needle roller complement bore diameter and tolerances for the drawn cup width.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 5593, Rolling bearings — Vocabulary
- ISO 10579, Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts
- ISO 14405-1, Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
- ISO/TS 17863, Geometrical product specification (GPS) — Tolerancing of moveable assemblies
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5593, ISO 14405-1 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
3.1
constraint diameter
D1c
diameter of the feature used in constraint condition to evaluate ΔFwgn characteristics
Note 1 to entry: It corresponds to the diameter of the master ring gauge in Annex B.
Bibliography
| 1 | ISO 286-1, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
| 2 | ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| 3 | ISO 1101, Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| 4 | ISO 1132-1, Rolling bearings — Tolerances — Part 1: Terms and definitions |
| 5 | ISO 1938-1:2015, Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size |
| 6 | ISO 8015, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules |
| 7 | ISO 14253-1, Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| 8 | ISO 14253-2, Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification |
| 9 | ISO 14638, Geometrical product specifications (GPS) — Matrix model |
| 10 | ISO 15241, Rolling bearings — Symbols for physical quantities |
| 11 | ISO 18203:2016, Steel — Determination of the thickness of surface-hardened layers |
| 12 | ISO 22872 1 , Rolling bearings — Geometrical product specifications (GPS) — Symbols, terms and definitions associated with GPS |