※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
国際規格 ISO 3310-3 は、技術委員会 ISO/TC 24, ふるい、ふるい分け、およびその他のサイジング方法によって作成されました。
ISO 3310 は、次の部分で構成されており、一般的なタイトルは「試験ふるい — 技術要件と試験」です。
- Part 1: 金属ワイヤー クロスのテストふるい
- Part 2: 穴あき金属板の試験ふるい
- Part 3: 電鋳シートのテストふるい
ISO 3310 のこの部分の附属書 A は、情報提供のみを目的としています。
序章
試験ふるいの精度は試験ふるいの開口部の寸法精度に依存するため、電鋳シートの開口部で達成できる非常に厳密な公差内のサイズの一貫性は、非常に細かい粒子材料の試験ふるいに魅力的です。
電鋳シートの試験用ふるいは、肉眼では非常に細かい穴が見えないため、特に注意して取り扱う必要があります。使用前後のこれらのふるいの洗浄に関する注意事項は、付録 A に記載されています。
1 スコープ
ISO 3310 のこの部分は、ふるい媒体が電気化学的に形成された開口部を備えた金属シートである試験ふるいの技術要件と対応する試験方法を指定します。
これは、ISO 565 に従って、サイズが 500 μm から 5 μm の範囲の円形 (円形) または正方形の開口部を持つ試験ふるいに適用されます。
2 規範的参照
次の規格には、このテキストでの参照を通じて、ISO 3310 のこの部分の規定を構成する規定が含まれています。発行の時点で、示された版は有効でした。すべての規格は改訂される可能性があり、ISO 3310 のこの部分に基づく契約の当事者は、以下に示す規格の最新版を適用する可能性を調査することをお勧めします。 IEC および ISO のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 565:1990, 試験ふるい - 金属金網、有孔金属板および電鋳シート - 開口部の公称サイズ。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 3310-3 was prepared by Technical Committee ISO/TC 24, Sieves, sieving and other sizing methods.
ISO 3310 consists of the following parts, under the general title Test sieves — Technical requirements and testing:
- Part 1: Test sieves of metal wire cloth
- Part 2: Test sieves of perforated metal plate
- Part 3: Test sieves of electroformed sheets
Annex A of this part of ISO 3310 is for information only.
Introduction
Since the accuracy of test sieving depends on the dimensional accuracy of the test sieve openings, the consistency of size within very close tolerances that can be achieved for the openings of electroformed sheet makes them attractive for test sieving of very fine particulate material.
Test sieves of electroformed sheet must be handled with particular care as the very fine apertures are invisible to the unaided eye. Notes on cleaning these sieves before and after use are given in annex A.
1 Scope
This part of ISO 3310 specifies the technical requirements and corresponding test methods for test sieves in which the sieving medium is a metal sheet with electrochemically formed apertures.
It applies to test sieves having round (circular) or square apertures ranging in size from 500 μm to 5 μm, in accordance with ISO 565.
2 Normative reference
The following standard contains provisions which, through reference in this text, constitute provisions of this part of ISO 3310. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this part of ISO 3310 are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
- ISO 565:1990, Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings.