※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
国際規格 ISO 3734 は、技術委員会 ISO/TC 28, 石油製品および潤滑油、小委員会 SC 6, バルク貨物輸送、説明責任、検査および調整によって作成されました。
この第 2 版は、技術的に改訂された第 1 版 (ISO 3734:1976) を取り消して置き換えるものです。
附属書 A および B は、この規格の不可欠な部分を形成します。
警告 — この国際規格の使用には、危険な物質、操作、および機器が含まれる場合があります。この国際規格は、その使用に関連する安全上の問題に対処することを意図していません。適切な安全衛生慣行を確立し、使用前に規制制限の適用可能性を判断することは、この国際規格の使用者の責任です。
1 スコープ
この国際規格は、遠心分離法を使用して残留燃料油中の水分と沈殿物の合計を実験室で測定する方法を規定しています。一部の油では、この方法を使用して水分または沈殿物含有量を取得することが困難です。このような状況に遭遇した場合、ISO 3733 および ISO 3735 を使用する必要があります。
注 —水と堆積物を測定する遠心分離法は、多くの場合、誤った結果をもたらす可能性があることが観察されています。これは、高速ミキサーを使用して代表的なサンプルを取得する場合に特に当てはまります。したがって、この方法は完全に満足できるものではなく、測定された水分量はほとんどの場合、実際の水分量よりも低くなります。
大量の水と堆積物は、特に存在する水にミネラル塩が含まれている場合、機器の取り扱いやエンジンやバーナーで操作上の問題を引き起こす可能性があります.フィルターや遠心分離機などの残留燃料油処理施設の設計は、燃焼前に除去する物質の最大量に基づいています。さらに製油所で処理される予定の残留燃料油も、腐食の問題を最小限に抑えるために、低レベルの水と沈殿物を必要とします。
2 参考文献
次の規格には、このテキストで参照することにより、この国際規格の規定を構成する規定が含まれています。発行の時点で、示されている版は有効でした。すべての規格は改訂される可能性があり、この国際規格に基づく契約の当事者は、以下に示す規格の最新版を適用する可能性を調査することをお勧めします。 IEC および ISO のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 3170:1988, 石油液体 - 手動サンプリング。
- ISO 3171:1988, 石油液体 - 自動パイプライン サンプリング。
- ISO 3733:— 1)石油製品および瀝青材料 — 水の測定 — 蒸留法。
- ISO 3735: — 2) 、原油および燃料油 — 沈殿物の測定 — 抽出方法。
- ISO 4787:1984, 実験用ガラス器具 - 容積測定用ガラス器具 - 容量の使用方法と試験方法。
- ISO 5272:1979, 工業用トルエン — 仕様。
- ISO 12937: —3) 、石油製品 — 水の測定 — カールフィッシャー電量法。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 3734 was prepared by Technical Committee ISO/TC 28, Petroleum products and lubricants, Subcommittee SC 6, Bulk cargo transfer, accountability, inspection and reconciliation.
This second edition cancels and replaces the first edition (ISO 3734:1976), which has been technically revised.
Annexes A and B form an integral part of this International Standard.
WARNING — The use of this International Standard may involve hazardous materials, operations and equipment. This International Standard does not purport to address any of the safety problems associated with its use. It is the responsibility of the user of this International Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1 Scope
This International Standard specifies a method for the laboratory determination of the sum of water and sediment in residual fuel oils using the centrifuge method. With some oils it is difficult to obtain water or sediment contents using this method. When this situation is encountered, ISO 3733 and ISO 3735 should be used.
NOTE — It has been observed that centrifugal methods of determination of water and sediment may, in many cases, give erroneous results. This is especially so when use of a high-speed mixer has been employed to obtain a representative sample. The method is therefore not entirely satisfactory and the amount of water determined is almost always lower than the actual water content.
Significant quantities of water and sediment can cause operational problems in handling equipment and in engines and burners, particularly when the water present contains mineral salts. Design of residual fuel oil treatment facilities, such as filters or centrifuges, is based on a maximum quantity of material to be removed before combustion. Residual fuel oils destined for further refinery processing also require low levels of water and sediment to minimize corrosion problems.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
- ISO 3170:1988, Petroleum liquids — Manual sampling.
- ISO 3171:1988, Petroleum liquids — Automatic pipeline sampling.
- ISO 3733:— 1)Petroleum products and bituminous materials — Determination of water — Distillation method.
- ISO 3735:— 2) , Crude petroleum and fuel oils — Determination of sediment — Extraction method.
- ISO 4787:1984, Laboratory glassware — Volumetric glassware — Methods for use and testing of capacity.
- ISO 5272:1979, Toluene for industrial use — Specifications.
- ISO 12937:— 3) , Petroleum products — Determination of water — Coulometric Karl Fischer method.