※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の開発に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2 ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自主的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html .
この文書は、欧州標準化委員会 (CEN) の技術委員会 CEN/TC 23, 可搬型ガスボンベと協力して、技術委員会 ISO/TC 58, ガスボンベ、小委員会 SC 2, シリンダー継手によって作成されました。 ISO と CEN 間の技術協力 (ウィーン協定)
この第 4 版は、技術的に改訂された第 3 版 (ISO 407:2004) を取り消して置き換えるものです。
前作からの主な変更点は以下の通り。
- 応力集中を避けるための半径の導入について、図 1 に注記を追加。
- 図 1 に次元mを追加。
- ピン インデックス ヨーク タイプ値接続の基本寸法の改訂 (表 2 を参照)
- 接続ヨークの設計要件の追加。
1 スコープ
このドキュメントは、最大 200 bar の作動圧力または最大 300 bar のテスト圧力、あるいはその両方の医療用ガス シリンダー用のピンインデックス ヨーク タイプのバルブ接続に適用されます。
注 1このタイプの接続は、主に小型シリンダー (5 リットル以下) に使用されます。
注記 2この文書では、工業用ガスの分野で広く使用されているため、ユニットバーが使用されています。ただし、bar は SI 単位ではなく、対応する圧力の SI 単位は Pa (1 bar = 10 5 Pa = 10 5 N/m 2 ) であることに注意してください。
このドキュメントは以下を指定します:
- 基本寸法;
- ヨークタイプのバルブ接続の代替設計の要件。
- コンセント接続用の穴とピンの寸法と位置。
また、ガスおよびガス混合物の出口接続用の穴とピンの寸法と位置も指定します。
2 参考文献
以下のドキュメントは、その内容の一部またはすべてがこのドキュメントの要件を構成するように、本文で参照されています。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 32, 医療用ガスボンベ — 内容物を識別するためのマーキング
3 用語と定義
このドキュメントには、用語と定義は記載されていません。
ISO と IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2, Cylinders fittings, in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 407:2004), which has been technically revised.
The main changes compared to the previous edition are as follows:
- addition of a note in Figure 1 on the introduction of a radius to avoid stress concentration;
- addition of dimension m in Figure 1;
- revision of the basic dimensions for pin index yoke type value connections (see Table 2);
- addition of a requirement for the design of the connecting yoke.
1 Scope
This document is applicable to pin-index yoke-type valve connections for medical gas cylinders, with a working pressure up to a maximum of 200 bar or test pressure up to a maximum of 300 bar, or both.
NOTE 1 This type of connection is primarily used for small cylinders (5 l or below).
NOTE 2 In this document the unit bar is used, due to its universal use in the field of technical gases. It should, however, be noted that bar is not an SI unit, and that the corresponding SI unit for pressure is Pa (1 bar = 105 Pa = 105 N/m2).
This document specifies:
- basic dimensions;
- requirements for alternative designs of the yoke-type valve connections;
- dimensions and positions for the holes and pins for the outlet connections.
It also specifies the dimensions and positions for the holes and pins for the outlet connections for gases and gas mixtures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 32, Gas cylinders for medical use — Marking for identification of content
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses: