※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (I EC) と緊密に協力しています。
技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
国際規格 ISO 4124 は、技術委員会 ISO/TC 28, 石油製品および潤滑油、小委員会 SC 2, 動的石油測定によって作成されました。
この規格の附属書 A, B, C, D, E, および F は、情報提供のみを目的としています。
セクション 1: 一般
1.1 範囲
動的測定システムでは、液体炭化水素のメーターの性能は、流動条件の変化によって変化します。流量、粘度、温度、圧力、製品の密度、および機械的摩耗。
この国際規格は、中央証明とオンライン証明の両方に適切な統計管理手順を使用して、そのような計器の性能を確立および監視するためのガイドとして作成されました。これらの手順は、あらゆるタイプの体積測定システムまたは質量測定システムによって行われる測定に適用できます。
管理限界の根拠となるデータを収集するために従うべき手順について説明します。これらのデータの信頼性を確立するための代替方法は、ISO 7278-3 に記載されています。
選択された性能特性をカバーするチャートの警告およびアクション管理限界を計算する方法、これらの管理チャートをその後の日常測定に適用する方法、およびそれらの解釈について説明します。実際の例は、適切な中央セクションとオンライン証明セクションに記載されています。
1.2 定義
この国際規格の目的のために、次の定義が適用されます。
1.2.1
証明証拠;較正
メーターを実際に通過する液体の体積とパイププルーバーの基準体積との関係によるメーターの性能の決定。
1.2.2
Kファクター
試験運転中にメーターによって生成されたパルス数(N)と、検出器間のパイプ試験機内の球体またはピストンによって押しのけられた液体の体積 ( V ) との関係。
通常、 K = N/Aです。この値は、ISO 7278-3 で説明されているパルス補間技術によって修正することをお勧めします。
1.2.3
メートル係数
メーター合計器によって示される体積に対する、パイプ プルーバーから得られる、メーターを通過した実際の体積の比率。
セクション 2: 統計測定
セクション 3: 中央証明
セクション 4: オンライン証明
セクション 5: 二次制御
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 4124 was prepared by Technical Committee ISO/TC 28, Petroleum products and lubricants, Subcommittee SC 2, Dynamic petroleum measurement.
Annexes A, B, C, D, E and F of this International Standard are for information only.
Section 1: General
1.1 Scope
In dynamic measuring systems the performance of meters for liquid hydrocarbons will vary with changes in flow conditions, viz. flowrate, viscosity, temperature, pressure, density of product, and with mechanical wear.
This International Standard has been prepared as a guide for establishing and monitoring the performance of such meters, using appropriate statistical control procedures for both central and on-line proving. These procedures may be applied to measurements made by any type of volumetric or mass metering system.
The procedures to be followed for collecting data, on which the control limits are based, are described. An alternative method for establishing the reliability of these data is described in ISO 7278-3.
Methods are described for calculating the warning and action control limits for the charts covering the selected performance characteristics, the application of these control charts to subsequent routine measurements, and their interpretation. Worked examples are given in the appropriate central and on-line proving sections.
1.2 Definitions
For the purposes of this International Standard, the following definitions apply.
1.2.1
proving; proof; calibration
Determination of the meter performance via the relationship between the volume of liquid actually passing through a meter and the reference volume of the pipe prover.
1.2.2
K-factor
Relationship between the number of pulses (N) generated by the meter during the proving run and the volume of liquid (V) displaced by the sphere or piston in the pipe prover between detectors.
Normally, K = N/V; it is recommended that this value be corrected by the pulse interpolation technique described in ISO 7278-3.
1.2.3
meter factor
Ratio of the actual volume passed through a meter, as derived from the pipe prover, to the volume indicated by the meter totalizer.