この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。
技術委員会によって採択された国際規格の草案は、ISO 理事会によって国際規格として承認される前に、承認のためにメンバー団体に回覧されます。それらは、投票するメンバー団体による少なくとも 75% の承認を必要とする ISO 手順に従って承認されます。
国際規格 ISO 4291 は、技術委員会 ISO/TC 57, Metology and properties of surfaceによって作成されました。
1 適用範囲と適用分野
この国際規格は、接触 (スタイラス) 器具を使用して半径の変化を測定することにより、真円度からの逸脱を決定する方法を指定します。
それは確立します
- a)器具の種類と一般的な要求事項
- b)器具の使用に関する推奨事項
- c)機器の校正及びその特性の検証の手順
この国際規格は、次のいずれかの中心に関して表される基準条件下で得られた、プロファイル変換の媒体によるワークピースの理想的な真円度からの逸脱の評価に適用されます。
- a)最小二乗円の中心;
- b)最小ゾーンサークルの中心;
- c)最小外接円の中心;
- d)最大内接円の中心。
これらの各センターには、独自の特定のアプリケーションがあります。最小二乗中心の位置は、附属書 F に示されている単純な明示的な式から計算できます。
測定されたプロファイルの真円度からの逸脱、手順、較正、および回転の系統誤差の決定は、それぞれ附属書 A から D で扱われます。附属書 E は、極座標グラフのプロットと読み取りに関する規則を示しています。
ノート
- 1プロファイル変換は ISO 6318 で定義されています。
- 2参照条件には、スタイラス、電波フィルターの周波数制限 (使用されている場合)、プロファイルのグラフまたはデジタル表示の許容偏心 (通常、その平均半径の 7% から 15%、付録 E を参照)、ワークピースのいくつかの特徴に関連する測定セクションまたはセクション。
2 参照
- ISO 6318, 真円度の測定 真円度の用語、定義、パラメーター。
3 つの定義
この国際規格の目的のために、ISO 6318 で与えられた定義が適用されます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the ISO Council. They are approved in accordance with ISO procedures requiring at least 75 % approval by the member bodies voting.
International Standard ISO 4291 was prepared by Technical Committee ISO/TC 57, Metrology and properties of surfaces.
1 Scope and field of application
This International Standard specifies a method for determining departures from roundness by measuring variations in radius by means of contact (stylus) instruments.
It establishes
- a) types of instruments and general requirements;
- b) recommendations for the use of instruments;
- c) procedures for calibration of instruments and verification of their characteristics.
This International Standard applies to the assessment of the departures from ideal roundness of a workpiece through the medium of a profile transformation, obtained under reference conditions, expressed with respect to any one of the following centres:
- a) centre of the least squares circle;
- b) centre of the minimum zone circle;
- c) centre of the minimum circumscribed circle;
- d) centre of the maximum inscribed circle.
Each of these centres may have its own particular application. The position of the least squares centre can be calculated from a simple explicit equation given in annex F.
Departures from roundness of the measured profile, procedure, calibration and determination of systematic errors of rotation are dealt with in annexes A to D, respectively. Annex E gives rules for plotting and reading polar graphs.
NOTES
- 1 Profile transformation is defined in ISO 6318.
- 2 Reference conditions include the stylus, frequency limitations of an electric wave filter (if used), permissible eccentricity of the graphical or digital representation of the profile (generally 7 % to 15 % of its mean radius, see annex E), the position of the measured section or sections relative to some feature of the workpiece.
2 Reference
- ISO 6318, Measurement of roundness Terms, definitions and parameters of roundness.
3 Definitions
For the purposes of this International Standard, the definitions given in ISO 6318 apply.