※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 2 部に規定されている規則に従って草案されています。
技術委員会の主な任務は、国際規格を作成することです。技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。
ISO 4625-2 は、技術委員会 ISO/TC 35, 塗料およびワニス、小委員会 SC 10, 塗料およびワニス用バインダーの試験方法によって、ASTM D01.34, Naval Storesと協力して作成されました。これは、ASTM D 6090-99, 樹脂軟化点の標準試験方法 (メトラー カップおよびボール法)と調和されています。
ISO 4625 は、一般タイトル「塗料およびワニス用バインダー - 軟化点の測定」の下に、次の部分で構成されています。
- Part 1: リングとボールの方法
- Part 2: カップ アンド ボール法
1 スコープ
ISO 4625 のこの部分では、カップアンドボール装置を使用して樹脂 (ロジンを含む) の軟化点を測定する方法が規定されており、ユーザー定義の条件下では、リングアンドボール装置を使用して得られる結果と同等の結果が得られます。ボール法 (ISO 4625-1)
2 規範的参照
この文書を適用するためには、以下の参照文書が不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 4625-1, 塗料およびワニス用バインダー — 軟化点の測定 — Part 1: 環球法
- ISO 5725-1, 測定方法と結果の精度 (真性と精度) — Part 1: 一般原則と定義
3 用語と定義
この文書の目的上、次の用語と定義が適用されます。
3.1
軟化点
底に6.35 mmの穴があり、直径8.7 mmのステンレス鋼のボールがカップ内の試験サンプルの上部の中心にある円筒形のカップに入った試験サンプルが、19 mmの距離下に流れて流れを遮断する温度。試験サンプルが空気中で一定速度で加熱されるときの光線
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4625-2 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 10, Test methods for binders for paints and varnishes, in collaboration with ASTM D01.34, Naval Stores. It has been harmonized with ASTM D 6090-99, Standard Test Method for Softening Point of Resins (Mettler Cup and Ball Method).
ISO 4625 consists of the following parts, under the general title Binders for paints and varnishes — Determination of softening point:
- Part 1: Ring-and-ball method
- Part 2: Cup-and-ball method
1 Scope
This part of ISO 4625 specifies a method for determining the softening point of resins (including rosin) by means of a cup-and-ball apparatus and can, under user-defined conditions, give results comparable to those obtained using the ring-and-ball method (ISO 4625-1).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 4625-1, Binders for paints and varnishes — Determination of softening point — Part 1: Ring-and-ball method
- ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
softening point
temperature at which a test sample in a cylindrical cup with a 6,35 mm hole in the bottom, with a stainless-steel ball 8,7 mm in diameter centred on top of the test sample in the cup, flows downward a distance of 19 mm to interrupt a light beam as the test sample is heated at a constant rate in air