※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
国際規格 ISO 5353 は、技術委員会 ISO/TC 127, 土工機械、小委員会 SC 2, 安全要件および人的要因によって作成されました。
この第 2 版は、第 1 版 (ISO 5353:1978) を取り消して置き換えるものであり、そのうちの技術的な改訂版です。
1 スコープ
この国際規格は、ISO 6165 で定義されている土工機械、および定義されている農業および林業用のトラクターおよび機械用に設計されたあらゆる種類のシートのシート インデックス ポイント (SIP) の位置を決定する際に使用する方法と装置を指定しています。 ISO 3339-
これにより、シート上の固定点に対する SIP の位置を定義するための統一された方法が提供されます。 SIP は、シート自体で、またはマシンの動作環境に配置されたシートで決定することができます。 SIPはシートの特徴です。したがって、シートメーカーによって指定される場合があります。
2 参考文献
次の規格には、このテキストで参照することにより、この国際規格の規定を構成する規定が含まれています。発行の時点で、示されている版は有効でした。すべての規格は改訂される可能性があり、この国際規格に基づく契約の当事者は、以下に示す規格の最新版を適用する可能性を調査することをお勧めします。 IEC および ISO のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 3339-0:1986, 農業および林業用のトラクターおよび機械 — 分類および用語 — 0: 分類システムと分類。
- ISO 6165:1987, 土工機械 - 基本タイプ - 語彙。
3 つの定義
この国際規格の目的のために、次の定義が適用されます。
3.1
シートインデックスポイント
SIP
5.3 に指定されているように座席に取り付けられている場合、図 1 に示す装置によって決定される座席の中央垂直面を指します。
注記 1: SIP は機械に対して固定されており、シートの調整および/または振動範囲を通じてシートと共に移動しません。
注記 2この国際規格によって確立され定義された SIP は、オペレータの作業場の設計目的のために、人間の胴体と胴体との間の理論的なピボット軸の座席中心線を通る中央垂直面上の交点と同等であると見なすことができます。太もも。
3.2
固定点
SIP が参照される製造元によって指定されたポイント。
例については、図 2 と 3 を参照してください。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 5353 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 2, Safety requirements and human factors.
This second edition cancels and replaces the first edition (ISO 5353:1978), of which it constitutes a technical revision.
1 Scope
This International Standard specifies a method and the device for use in determining the position of the seat index point (SIP) for any kind of seat designed for earth-moving machinery as defined in ISO 6165, and tractors and machinery for agriculture and forestry as defined in ISO 3339-0.
This provides a uniform method for defining the location of the SIP in relation to a fixing point on the seat. The SIP may be determined on a seat by itself or with the seat located in its operating environment on the machine. The SIP is a characteristic of the seat; therefore, it may be specified by the seat manufacturer.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
- ISO 3339-0:1986, Tractors and machinery for agriculture and forestry — Classification and terminology — 0: Classification system and classification.
- ISO 6165:1987, Earth-moving machinery — Basic types — Vocabulary.
3 Definitions
For the purposes of this International Standard, the following definitions apply.
3.1
seat index point
SIP
Point on the central vertical plane of the seat as determined by the device shown in figure 1, when installed in the seat as specified in 5.3.
Note 1 to entry: The SIP is fixed with respect to the machine and does not move with the seat through its adjustment and/or oscillation range.
Note 2 to entry: The SIP as established and defined by this International Standard may be considered, for operator work-place design purposes, to be equivalent to the intersection on the central vertical plane through the seat centreline of the theoretical pivot axis between a human torso and thighs.
3.2
fixing point
Point specified by the manufacturer to which the SIP is referenced.
See figures 2 and 3 for examples.