※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令で指定された規則に従って起草されます。 2.
技術委員会の主な任務は、国際規格を準備することです。技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
このドキュメントの一部の要素が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。
ISO 5748 は、技術委員会 ISO/TC 29, 小型工具、小委員会 SC 10, ネジとナット、ペンチとニッパーの組立工具によって作成されました。
この第 3 版は、技術的に改訂された第 2 版 (ISO 5748:1988) を取り消して置き換えるものです。
1 スコープ
この国際規格は、ISO 5744 に準拠して機能する適性を検証するために、エンド カット ニッパーの主な寸法とニッパーの試験値を指定します。一般的な技術要件は、ISO 5743 に記載されています。
この国際規格に示されているエンド ニッパーは単なる例であり、製造業者の設計に影響を与えることを意図したものではありません。
2 参考文献
本書の適用には、以下の参考文献が不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 5743, プライヤーとニッパー — 一般的な技術要件
- ISO 5744:2004, プライヤーとニッパー — 試験方法
参考文献
| [1] | ISO 5742, プライヤーとニッパー — 命名法 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5748 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers.
This third edition cancels and replaces the second edition (ISO 5748:1988) which has been technically revised.
1 Scope
This International Standard specifies the principal dimensions of end cutting nippers and the test values for the nippers in order to verify their aptitude to function in conformity with ISO 5744. General technical requirements are given in ISO 5743.
The end nippers illustrated in this International Standard are examples only and are not intended to affect the manufacturer's design.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 5743, Pliers and nippers — General technical requirements
- ISO 5744:2004, Pliers and nippers — Methods of test
Bibliography
| [1] | ISO 5742, Pliers and nippers — Nomenclature |