※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の開発に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令第 1 Part に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part の編集規則に従って起草されました ( www.iso.org/directives を参照)
ISO は、この文書の実装には特許の使用が含まれる可能性があることに注意を促します。 ISO は、請求された特許権に関する証拠、有効性、または適用可能性に関していかなる立場もとりません。この文書の発行日の時点で、ISO はこの文書の実装に必要となる可能性のある特許の通知を受け取っていません。ただし、実装者は、これが www.iso.org/patents で入手可能な特許データベースから取得できる最新の情報を表していない可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易の技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html
この文書は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 4, 製品 (ホース以外)によって作成されました。
この第 3 版は、技術的に改訂された第 2 版 (ISO 5892:2013) を廃止し、置き換えるものです。
主な変更点は次のとおりです。寿命推定が条項 9 のオプション要件として追加されました。
1 スコープ
この文書は、建物のシールおよび支持用途における予備成形固体加硫ゴム構造ガスケットの材料要件を指定します。
注非サポートガスケットの仕様は ISO 3934 に記載されています。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 37, ゴム、加硫または熱可塑性プラスチック — 引張応力-ひずみ特性の決定
- ISO 48-4, ゴム、加硫または熱可塑性プラスチック — 硬度の測定 — Part 4: デュロメーター法による押し込み硬度 (ショア硬度)
- ISO 188:2023, ゴム、加硫または熱可塑性 - 加速老化試験および耐熱性試験
- ISO 812:2017, ゴム、加硫または熱可塑性プラスチック — 低温脆性の測定
- ISO 815-1, ゴム、加硫ゴムまたは熱可塑性樹脂 — 圧縮永久歪みの測定 — Part 1: 周囲温度または高温で
- ISO 815-2, ゴム、加硫ゴムまたは熱可塑性樹脂 — 圧縮永久歪みの測定 — Part 2: 低温で
- ISO 1382, ゴム - 語彙
- ISO 1431-1, ゴム、加硫または熱可塑性プラスチック — オゾンクラッキングに対する耐性 — Part 1: 静的および動的ひずみ試験
- ISO 3302-1, ゴム — 製品の公差 — Part 1: 寸法公差
- ISO 3384-1:2024, ゴム、加硫または熱可塑性プラスチック — 圧縮時の応力緩和の測定 — Part 1: 一定温度での試験
- ISO 11346, ゴム、加硫または熱可塑性プラスチック — 寿命と使用最高温度の推定
3 用語と定義
この文書の目的のために、ISO 1382 および以下に示されている用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
構造ガスケット
ガラス基板などを直接支持し、部品の防水性と気密性を高める建築用 ガスケット (3.2)
注記 1:構造ガスケットは、ガスケットと ロックストリップ (3.3) で構成されます。
3.2
ガスケット
メガネとサポートフレームの両方をサポートするチャネルを備えたコンポーネント
注記 1: 2 つのチャネルを持つガスケットはダブルチャネルガスケットと呼ばれ、1 つのチャネルを持つガスケットはシングルチャネルガスケットと呼ばれます。
3.3
ロックストリップ
必要な水密性と気密性を確保するためにロックストリップのキャビティに挿入される部品
3.4
使用温度
ガスケット (3.2) が使用される温度where
参考文献
| 1 | ISO 1431-3, ゴム、加硫または熱可塑性プラスチック — オゾン亀裂に対する耐性 — Part 3: 実験室試験チャンバー内のオゾン濃度を測定するための参考方法および代替方法 |
| 2 | ISO 3865, ゴム、加硫または熱可塑性プラスチック — 有機材料との接触による汚れの試験方法 |
| 3 | ISO 3934, ゴム、加硫および熱可塑性プラスチック — 建物で使用されるプリフォームガスケット — 分類、仕様、および試験方法 |
| 4 | ISO 15821, ドアセットと窓 — 動圧下での水密性試験 — サイクロン的側面 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s) which may be required to implement this document. However, implementers are cautioned that this may not represent the latest information, which may be obtained from the patent database available at www.iso.org/patents . ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses).
This third edition cancels and replaces the second edition (ISO 5892:2013), which has been technically revised.
The main change is as follows: lifetime estimation has been added as an optional requirement in Clause 9.
1 Scope
This document specifies the material requirements for preformed, solid vulcanized rubber structural gaskets in sealing and supporting applications for buildings.
NOTE Specifications for non-supporting gaskets are given in ISO 3934.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
- ISO 48-4, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 4: Indentation hardness by durometer method (Shore hardness)
- ISO 188:2023, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
- ISO 812:2017, Rubber, vulcanized or thermoplastic — Determination of low-temperature brittleness
- ISO 815-1, Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures
- ISO 815-2, Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures
- ISO 1382, Rubber — Vocabulary
- ISO 1431-1, Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing
- ISO 3302-1, Rubber — Tolerances for products — Part 1: Dimensional tolerances
- ISO 3384-1:2024, Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression — Part 1: Testing at constant temperature
- ISO 11346, Rubber, vulcanized or thermoplastic — Estimation of life-time and maximum temperature of use
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1382 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
3.1
structural gasket
building gasket (3.2) that directly supports glass substrates, etc. and makes components watertight and airtight
Note 1 to entry: A structural gasket consists of gaskets and lock strips (3.3) .
3.2
gasket
component with channels which support both glasses and support frames
Note 1 to entry: A gasket that has two channels is called a double-channel gasket and a gasket that has one channel is called a single-channel gasket.
3.3
lock strip
component that is inserted into the lock-strip cavities for ensuring the required watertightness and airtightness
3.4
working temperature
temperature range where the gasket (3.2) is intended to be used
Bibliography
| 1 | ISO 1431-3, Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 3: Reference and alternative methods for determining the ozone concentration in laboratory test chambers |
| 2 | ISO 3865, Rubber, vulcanized or thermoplastic — Methods of test for staining in contact with organic material |
| 3 | ISO 3934, Rubber, vulcanized and thermoplastic — Preformed gaskets used in buildings — Classification, specifications and test methods |
| 4 | ISO 15821, Doorsets and windows — Water-tightness test under dynamic pressure — Cyclonic aspects |