※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の開発に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2 ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自主的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html .
この文書は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 2, 試験および分析によって作成されました。
この第 3 版は、技術的に改訂された第 2 版 (ISO 6101-1:1991) を取り消して置き換えるものです。
旧版との主な変更点は以下の通りです。
- 有機物を破壊する手順がさらに詳しく説明されています。
- 9.2 の式 (2) は、亜鉛含有量がキログラムあたりのミリグラムで表されるように変更されました。
- 付属書 B の精度データが更新されました。
ISO 6101 シリーズのすべての部品のリストは、ISO Web サイトで見つけることができます。
警告 1このドキュメントを使用する人は、通常の実験室の慣行に精通している必要があります。このドキュメントは、その使用に関連する安全上の問題のすべてに対処することを目的としていません。適切な安全衛生慣行を確立し、その他の制限の適用可能性を判断することは、ユーザーの責任です。
警告 2このドキュメントで指定されている特定の手順には、地域の環境に危険を及ぼす可能性のある物質の使用または生成、または廃棄物の生成が含まれる場合があります。使用後の安全な取り扱いと廃棄に関する適切な文書を参照する必要があります。
1 スコープ
この文書は、ゴムの亜鉛含有量を決定するための原子吸光分析法を規定しています。
この方法は、亜鉛含有量が最低 0.05% (質量分率) の生ゴムおよびゴム製品に適用できます。試験部分の質量および/または使用する溶液の濃度を適切に調整すれば、この限度未満の亜鉛含有量を決定することができます。標準添加法を使用すると、検出下限が低下する可能性があります。
2 参考文献
以下のドキュメントは、その内容の一部またはすべてがこのドキュメントの要件を構成するように、本文で参照されています。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
このドキュメントには、用語と定義は記載されていません。
ISO と IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
参考文献
| [1] | ISO/TR 9272 2 、ゴムおよびゴム製品 - 試験方法規格の精度の決定 |
| [2] | ISO 19983, ゴム — 試験方法の精度の決定 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis.
This third edition cancels and replaces the second edition (ISO 6101-1:1991), which has been technically revised.
The main changes compared to the previous edition are as follows.
- The procedure for the destruction of organic matter is further detailed.
- Formula (2) in 9.2 has been changed to zinc content being expressed as milligram per kilogram.
- Precision data have been updated in Annex B.
A list of all parts in the ISO 6101 series can be found on the ISO website.
WARNING 1 Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to determine the applicability of any other restrictions.
WARNING 2 Certain procedures specified in this document might involve the use or generation of substances, or the generation of waste, that could constitute a local environmental hazard. Reference should be made to appropriate documentation on safe handling and disposal after use.
1 Scope
This document specifies an atomic absorption spectrometric method for the determination of the zinc content of rubbers.
The method is applicable to raw rubber and rubber products having zinc contents at a minimum of 0,05 % (mass fraction). Zinc contents below this limit can be determined, provided that suitable adjustments are made to the mass of the test portion and/or to the concentrations of the solutions used. The use of the standard additions method might lower the bottom limit of detection.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 123, Rubber latex — Sampling
- ISO 124, Latex, rubber — Determination of total solids content
- ISO 247-1, Rubber — Determination of ash — 1: Combustion method
- ISO 648, Laboratory glassware — Single-volume pipettes
- ISO 1042, Laboratory glassware — One-mark volumetric flasks
- ISO 1772, Laboratory crucibles in porcelain and silica
- ISO 1795, Rubber, raw natural and raw synthetic — Sampling and further preparative procedures
- ISO 4793, Laboratory sintered (fritted) filters — Porosity grading, classification and designation
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
Bibliography
| [1] | ISO/TR 9272 2 , Rubber and rubber products — Determination of precision for test method standards |
| [2] | ISO 19983, Rubber — Determination of precision of test methods |