※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について国際電気標準会議 (IEC) と緊密に協力しています。
技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
国際規格 ISO 6410-1 は、技術委員会 ISO/TC 10, 技術図面、製品定義および関連文書、小委員会 SC 6, 機械工学文書によって作成されました。
ISO 6410-1 のこの初版は、技術改訂版である ISO 6410:1981 を廃止し、置き換えるものです。
ISO 6410 は、 「技術図面 - ねじ山およびねじ部品」という一般タイトルの下に、次の部分で構成されています。
- Part 1: 一般的な規約
- Part 2: ねじ山インサート
- Part 3: 簡略化された表現
ISO 6410 のこの部分の付録 A は情報提供のみを目的としています。
導入
ISO 6410 は、ファスナーの設計、製造、取り付けに関わるさまざまな関係者の間で共通のコミュニケーション手段を提供するために考案されました。
業界内の要件は大きく異なります。この事実を認識して、ISO 6410 は 3 つの部分で構成されています (序文を参照)
1 スコープ
ISO 6410 のこの部分では、技術図面上でねじ山とねじ部品を表現する方法を指定します。
2 規範的参照
以下の規格には、本書での参照を通じて ISO 6410 のこの部分の規定を構成する規定が含まれています。発行時点では、示されている版は有効でした。すべての規格は改訂される可能性があり、ISO 6410 のこの部分に基づく協定の当事者は、以下に示す規格の最新版を適用する可能性を調査することが推奨されます。 IEC および ISO のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 128:1982, 技術図面 — 表示の一般原則。
- ISO 129:1985, 技術図面 — 寸法 — 一般原則、定義、実行方法、および特別な表示。
- ISO 225:1983, ファスナー - ボルト、ネジ、スタッド、ナット - 寸法の記号と指定。
- ISO 4753:1983, ファスナー 外径 ISO ねじを備えた部品の端。
- ISO 6410-3:1993, 技術図面 — ねじ山およびねじ部品 — Part 3: 簡略化された表現。
付録A
参考文献
| 1 | ISO 228-1:1982, ねじ山where 耐圧接合が行われていない管ねじ — Part 1: 指定、寸法および公差。 |
| 2 | ISO 261:— 3) 、 ISO 汎用メートルねじ — 一般計画。 |
| 3 | ISO 262:— 4) 、 ISO 汎用メートルネジ — ネジ、ボルト、ナットの選択されたサイズ。 |
| 4 | ISO 965-1:1980, ISO 汎用メートルねじ - 公差 - Part 1: 原則と基本データ。 |
| 5 | ISO 2902:1977, ISO メートル台形ねじ - 一般計画。 |
| 6 | ISO 5835:1991, 外科用インプラント — 六角ドライブ接続を備えた金属骨ネジ、ヘッドの球面下面、非対称ネジ — 寸法。 |
| 7 | ねじ山の国際ガイド — さまざまな国の規格におけるねじ山の記号、プロファイル、および指定、Beuth Verlag, ベルリン。 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 6410-1 was prepared by Technical Committee ISO/TC 10, Technical drawings, product definition and related documentation, Sub-Committee SC 6, Mechanical engineering documentation.
This first edition of ISO 6410-1 cancels and replaces ISO 6410:1981, of which it constitutes a technical revision.
ISO 6410 consists of the following parts, under the general title Technical drawings — Screw threads and threaded parts:
- Part 1: General conventions
- Part 2: Screw thread inserts
- Part 3: Simplified representation
Annex A of this part of ISO 6410 is for information only.
Introduction
ISO 6410 has been devised to provide a universal means of communication among the various interests involved in the design, manufacture and installation of fasteners.
Requirements within industries vary considerably; in recognition of this fact, ISO 6410 is presented in three parts (see foreword).
1 Scope
This part of ISO 6410 specifies methods for representing screw threads and threaded parts on technical drawings.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 6410. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 6410 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
- ISO 128:1982, Technical drawings — General principles of presentation.
- ISO 129:1985, Technical drawings — Dimensioning — General principles, definitions, methods of execution and special indications.
- ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
- ISO 4753:1983, Fasteners Ends of parts with external metric ISO thread.
- ISO 6410-3:1993,Technical drawings — Screw threads and threaded parts — Part 3: Simplified representation.
Annex A
Bibliography
| 1 | ISO 228-1:1982, Pipe threads where pressuretight joints are not made on the threads — Part 1: Designation, dimensions and tolerances. |
| 2 | ISO 261:— 3) , ISO general-purpose metric screw threads — General plan. |
| 3 | ISO 262:— 4) , ISO general-purpose metric screw threads — Selected sizes for screws, bolts and nuts. |
| 4 | ISO 965-1:1980, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data. |
| 5 | ISO 2902:1977, ISO metric trapezoidal screw threads — General plan. |
| 6 | ISO 5835:1991, Implants for surgery — Metal bone screws with hexagonal drive connection, spherical under-surface of head, asymmetrical thread — Dimensions. |
| 7 | International guide to screw threads — Symbols, profiles and designations of threads in standards of various countries, Beuth Verlag, Berlin. |