この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。
技術委員会によって採択された国際規格草案は、ISO 理事会によって国際規格として承認される前に、承認を得るために加盟団体に回覧されます。これらは、加盟団体の投票による少なくとも 75% の承認を必要とする ISO 手順に従って承認されます。
国際規格 ISO 6453 は、ISO/TC 45ゴムおよびゴム製品技術委員会によって作成されました。
ユーザーは、特に明記されていない限り、すべての国際規格は随時改訂されること、および他の国際規格への言及はその最新版を意味することに留意する必要があります。
0 はじめに
柔軟な発泡ポリ塩化ビニル (PVC) シートには、次の 2 つのタイプがあります。
タイプ 1 — オープンセル材料。
タイプ 2 — クローズドセル素材。
シートは、ISO 2439 に従って測定された硬度指数に基づいて等級分けされます。タイプ 1 シートの場合は単一の硬度レベルが指定されますが、タイプ 2 シートの場合は範囲が指定されます。約 100 mm までの任意の厚さのシートについては、材料の押し込み硬度指数が指定されています。タイプ 2 の材料の場合、通常は 50 mm よりはるかに薄い厚さでしか入手できませんが、多数の層からなる試験片を使用する必要があるため、製品の押し込み硬さ指数が指定されます。
この国際規格の要件に準拠し、難燃性を有すると主張されるシートが市販されているかどうかに注目が集まっています。自動車業界では ISO 3795 (FMVSS 302) が一般的に使用されていますが、可燃性について一般に受け入れられている試験方法がないため、このタイプのシートに対する特定の要件をこの国際規格に含めることはできません。このような方法を考案する努力が国内レベルでも国際レベルでも行われています。難燃性の特性を持つシートは通常、ピンク色に着色されているか、適切な識別情報が印刷されています。
さらなる曇りや吸音への要求、低温特性の評価方法の改善なども検討中です。
1 適用範囲と適用分野
この国際規格は、誘電 (HF) 溶接を伴う用途 (パディングやキルティングなど) で使用する、厚さ 100 mm までのシートの形の柔軟なセルラー PVC の要件を指定します。
2 種類のシートは次のように指定されます。
タイプ 1 — オープンセル材料。
タイプ 2 — クローズドセル素材。
参考文献2件
- ISO 105, テキスタイル - 色堅牢度のテスト
セクション A03, 染色を評価するためのグレースケール。
セクション B01, 耐光堅牢度: 日光。 - ISO 845, 気泡ゴムおよびプラスチック — 見掛け密度の測定。
- ISO 1798, 柔軟な気泡材料 - 引張強度と破断伸びの測定。
- ISO 1856, ポリマー材料、セルラーフレキシブル — 圧縮永久歪みの決定。
- ISO 1923, 気泡プラスチックおよびゴム - 長さ寸法の決定。
- ISO 2439, ポリマー材料、セルフレキシブル — 硬度の測定 (押し込み技術)
- ISO 2440, 柔軟なセル材料 - 加速老化試験。
- ISO 3795, 道路車両 — 自動車の内装材の燃焼挙動の決定。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the ISO Council. They are approved in accordance with ISO procedures requiring at least 75 % approval by the member bodies voting.
International Standard ISO 6453 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products.
Users should note that all International Standards undergo revision from time to time and that any reference made herein to any other International Standard implies its latest edition, unless otherwise stated.
0 Introduction
Flexible cellular polyvinylchloride (PVC) sheeting is available in two types as follows:
type 1 — open cell material ;
type 2 — closed cell material.
The sheeting is graded according to hardness index, measured in accordance with ISO 2439. For type 1 sheeting, a single hardness level is specified, but for type 2 sheeting, a range is specified. For sheeting which is available in any thickness up to approximately 100 mm, the material indentation hardness index is specified. For type 2 material, which is normally available only in thicknesses much less than 50 mm, it is necessary to use a test piece consisting of a number of plies, and the product indentation hardness index is therefore specified.
Attention is drawn to the commercial availability of sheeting complying with the requirements of this International Standard and claimed to have flame retardant characteristics. Specific requirements for this type of sheeting cannot be included in this International Standard because no generally accepted method of test for flammability is available, although ISO 3795 (FMVSS 302) is commonly used in the motor industry. Efforts to devise such a method are being made at both the national and international levels. Sheeting with flame-retardant characteristics is normally coloured pink or printed with appropriate identification.
Further requirements on fogging and sound absorbance, and improvements in the method for assessing low-temperature characteristics, are under consideration.
1 Scope and field of application
This International Standard specifies requirements for flexible cellular PVC in the form of sheets up to 100 mm in thickness for use in applications involving dielectric (HF) welding (for example padding and quilting).
Two types of sheeting are specified as follows:
type 1 — open cell material ;
type 2 — closed cell material.
2 References
- ISO 105, Textiles — Tests for colour fastness
Section A03, Grey scale for assessing staining.
Section B01, Colour fastness to light: Daylight. - ISO 845, Cellular rubbers and plastics — Determination of apparent density.
- ISO 1798, Flexible cellular materials — Determination of tensile strength and elongation at break.
- ISO 1856, Polymeric materials, cellular flexible — Determination of compression set.
- ISO 1923, Cellular plastics and rubbers — Determination of linear dimensions.
- ISO 2439, Polymeric materials, cellular flexible — Determination of hardness (indentation technigue).
- ISO 2440, Flexible cellular materials — Accelerated ageing tests.
- ISO 3795, Road vehicles — Determination of burning behaviour of interior materials for motor vehicles.