※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化機関 (ISO 加盟団体) の世界的な連合です。国際規格の開発作業は、ISO 技術委員会を通じて行われます。技術委員会が設置された主題に関心のあるすべての会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。
技術委員会によって採択された国際規格の草案は、ISO 理事会によって国際規格として承認される前に、承認のために加盟機関に回覧されます。
1972 年以前は、技術委員会の作業の結果が ISO 勧告として発行されていました。これらの文書は現在、国際規格に変換されている過程にあります。このプロセスの一環として、技術委員会 ISO/TC 60 は ISO 勧告 R 677 を見直し、技術的に変換に適していると判断しました。したがって、国際規格 ISO 677 は、技術的に同一である ISO 勧告 R 677-1968 に取って代わります。
ISO 勧告 R 677 は、次の国の加盟機関によって承認されました。
| オーストラリア | ドイツ | 南アフリカ共和国 |
| オーストリア | ハンガリー | スペイン |
| ベルギー | インド | スイス |
| ブラジル | イスラエル | 七面鳥 |
| チリ | イタリア | イギリス |
| チェコスロバキア | オランダ | ソビエト連邦 |
| フランス | ポーランド | ユーゴスラビア |
この勧告に反対を表明した加盟団体はなかった。
次の国の加盟団体は、ISO/R 677 の国際規格への変換を承認しませんでした:
| チェコスロバキア |
1 適用範囲と適用分野
この国際規格は、一定の底部クリアランスを有する、一般工学および重工業用の直角歯車の基本ラックの寸法特性を指定します。これらの歯車ペアでは、一方の歯車の先端角度は、設計されたシャフト角度と相手歯車の歯底角度の差に等しくなります。
2 定義
2.1
ベーシックラック
ラック。そのプロファイルは、歯面に直角な平面上で無限に大きな直径を持つクラウン ギアの歯面の断面に対応します。
このプロファイルは、まっすぐな歯を持つかさ歯車のシステムの基礎として使用されます。
2.2
基準線
歯の寸法が指定されている基準となる、基本ラックのプロファイル上の直線。
FOREWORD
ISO (the International Organization for Standardization) is a worldwide federation of national standards institutes (ISO Member Bodies). The work of developing International Standards is carried out through ISO Technical Committees. Every Member Body interested in a subject for which a Technical Committee has been set up has the right to be represented on that Committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the Technical Committees are circulated to the Member Bodies for approval before their acceptance as International Standards by the ISO Council.
Prior to 1972, the results of the work of the Technical Committees were published as ISO Recommendations; these documents are now in the process of being transformed into International Standards. As part of this process, Technical Committee ISO/TC 60 has reviewed ISO Recommendation R 677 and found it technically suitable for transformation. International Standard ISO 677 therefore replaces ISO Recommendation R 677-1968 to which it is technically identical.
ISO Recommendation R 677 was approved by the Member Bodies of the following countries:
| Australia | Germany | South Africa, Rep. of |
| Austria | Hungary | Spain |
| Belgium | India | Switzerland |
| Brazil | Israel | Turkey |
| Chile | Italy | United Kingdom |
| Czechoslovakia | Netherlands | U.S.S.R. |
| France | Poland | Yugoslavia |
No Member Body expressed disapproval of the Recommendation.
The Member Body of the following country disapproved the transformation of ISO/R 677 into an International Standard:
| Czechoslovakia |
1 SCOPE AND FIELD OF APPLICATION
This International Standard specifies the dimensional characteristics of the basic rack of straight bevel gears, for general engineering and heavy engineering, having a constant bottom clearance. In these gear pairs the tip angle of one gear is equal to the difference between the designed shaft angle and the root angle of the mating gear.
2 DEFINITIONS
2.1
basic rack
Rack, the profile of which corresponds to a section of the tooth surface of a crown gear of infinitely large diameter on a plane at right angles to the tooth surfaces.
This profile is used as the basis of a system of bevel gears having straight teeth.
2.2
reference line
Straight line on the profile of the basic rack, with reference to which the tooth dimensions are specified.