※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 2 部に規定されている規則に従って草案されています。
技術委員会の主な任務は、国際規格を作成することです。技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
ISO 7143 は、ISO/TC 35 技術委員会「塗料およびワニス」 、小委員会 SC 10 「塗料およびワニス用バインダーの試験方法」によって、CEN 技術委員会 CEN/TC 139「塗料およびワニス」と協力して作成されました。
この第 3 版は、技術的に改訂された第 2 版 (ISO 7143:2000) を廃止し、置き換えるものです。
主な変更点は以下のとおりです。
- a)水性塗料は、この規格に従って指定されていないため、範囲から除外されました。
- b)分子量の決定が表 1 に追加されました。
- c)基準参照が更新され、本文が編集上改訂されました。
読者は、ISO 12000 がポリマー分散液と格子に関する定義を示し、それらの特性の測定に適用できる試験方法を特定していることに注意してください。 ISO 12000 は、水性および非水性ポリマー分散液の両方、および合成ゴムラテックスを含む合成および天然由来の製品を対象としています。これは、ISO/TC 45 のゴムおよびゴム製品と緊密に連携して、ISO/TC 61 技術委員会「プラスチック」 、小委員会 SC 9 「熱可塑性プラスチック材料」によって作成されました。
ISO 7143:2007 のこの修正版では、序文の 4 番目の段落にある規格の参照番号が ISO 7143 に修正されました。
1 スコープ
この国際規格は、バインダー、すなわちポリマーおよびコポリマーの水性分散液および溶液、特に水性塗料の原料として使用されるものを特性評価するための試験方法を規定しています。決定される特性は、乾燥システムと硬化システムのどちらをテストするかによって異なります。
2 規範的参照
この文書を適用するためには、以下の参照文書が不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 976, ゴムおよびプラスチック — ポリマー分散液およびゴムラテックス — pH の測定
- ISO 2115, プラスチック - ポリマー分散液 - 白色点温度と最低フィルム形成温度の決定
- ISO 2811-1, 塗料およびワニス — 密度の測定 — Part 1: 比重瓶法
- ISO 3219, プラスチック — 液体状態またはエマルジョンまたは分散液のポリマー/樹脂 — 定義されたせん断速度での回転粘度計を使用した粘度の測定
- ISO 3251, 塗料、ワニスおよびプラスチック — 不揮発性物質含有量の測定
- ISO 4576, プラスチック - ポリマー分散液 - ふるい残留物の測定 (総粒子および凝塊含有量)
- ISO 11357-2, プラスチック — 示差走査熱量測定 (DSC) — Part 2: ガラス転移温度の測定
- ISO 11359-2, プラスチック — 熱機械分析 (TMA) — Part 2: 線熱膨張係数とガラス転移温度の決定
- ISO 13741-1, プラスチック/ゴム — ポリマー分散液およびゴムラテックス (天然および合成) — キャピラリーカラムガスクロマトグラフィーによる残留モノマーおよびその他の有機成分の定量 — Part 1: 直接液体注入法
- ISO 13741-2, プラスチック/ゴム — ポリマー分散液およびゴムラテックス (天然および合成) — キャピラリーカラムガスクロマトグラフィーによる残留モノマーおよびその他の有機成分の定量 — Part 2: ヘッドスペース法
- ISO 13885-1, 塗料およびワニス用バインダー — ゲル浸透クロマトグラフィー (GPC) — Part 1: 溶離液としてのテトラヒドロフラン (THF)
- ISO 15528, 塗料、ワニスおよび塗料およびワニスの原料 — サンプリング
- ISO 15880, 塗料、ワニスおよびバインダー - 水性塗料およびバインダーの MEQ 値の決定
- ISO 16805, 塗料およびワニス用バインダー - ガラス転移温度の測定
3 用語と定義
この文書の目的上、次の用語と定義が適用されます。
3.1
ポリマーディスパージョン
安定した状態でポリマー材料を含み、連続液相、通常は水 (水性分散液) または有機液体 (非水性分散液、NAD) に細かく分散された液体または半液体材料、通常は乳白色。
[出典:ISO 4618:2006]
3.2
水性バインダー
揮発分の主成分が水であるバインダー
参考文献
| 1 | ISO 4618:2006, 塗料およびワニス — 用語と定義 |
| 2 | ISO 12000, プラスチック/ゴム — ポリマー分散液およびゴムラテックス (天然および合成) — 試験方法の定義とレビュー |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
ISO 7143 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 10, Test methods for binders for paints and varnishes, in collaboration with CEN Technical Committee CEN/TC 139, Paints and varnishes.
This third edition cancels and replaces the second edition (ISO 7143:2000), which has been technically revised.
The major changes are as follows:
- a) water-based coating materials have been excluded from the scope because these products are not specified in accordance with this standard;
- b) the determination of molecular mass has been added to Table 1;
- c) the normative references have been updated and the text has been editorially revised.
Readers should note that ISO 12000 gives definitions relative to polymer dispersions and lattices, and identifies the test methods applicable to the determination of their properties. ISO 12000 covers both aqueous and non-aqueous polymer dispersions, and products of synthetic and natural origin, including synthetic rubber latices. It was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials, in close collaboration with ISO/TC 45, Rubber and rubber products.
In this corrected version of ISO 7143:2007, the reference number of the standard in the fourth paragraph of the foreword has been corrected to read ISO 7143.
1 Scope
This International Standard specifies methods of test for characterizing binders, i.e. aqueous dispersions and solutions of polymers and copolymers, in particular those used as raw materials for water-based coating materials. The properties determined will depend on whether a drying or curing system is tested.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 976, Rubber and plastics — Polymer dispersions and rubber latices — Determination of pH
- ISO 2115, Plastics — Polymer dispersions — Determination of white point temperature and minimum film-forming temperature
- ISO 2811-1, Paints and varnishes — Determination of density — Part 1: Pyknometer method
- ISO 3219, Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate
- ISO 3251, Paints, varnishes and plastics — Determination of non-volatile-matter content
- ISO 4576, Plastics — Polymer dispersions — Determination of sieve residue (gross particle and coagulum content)
- ISO 11357-2, Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature
- ISO 11359-2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
- ISO 13741-1, Plastics/rubber — Polymer dispersions and rubber latices (natural and synthetic) — Determination of residual monomers and other organic components by capillary-column gas chromatography — Part 1: Direct liquid injection method
- ISO 13741-2, Plastics/rubber — Polymer dispersions and rubber latices (natural and synthetic) — Determination of residual monomers and other organic components by capillary-column gas chromatography — Part 2: Headspace method
- ISO 13885-1, Binders for paints and varnishes — Gel permeation chromatography (GPC) — Part 1: Tetrahydrofuran (THF) as eluent
- ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
- ISO 15880, Paints, varnishes and binders — Determination of MEQ value of water-based coating materials and binders
- ISO 16805, Binders for paints and varnishes — Determination of glass transition temperature
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
polymer dispersion
liquid or semi-liquid material, usually milkwhite, containing the polymeric material in a stable condition, finely dispersed in a continuous liquid phase, normally water (aqueous dispersion) or an organic liquid (non-aqueous dispersion, NAD)
[SOURCE:ISO 4618:2006]
3.2
water-based binder
binder in which the main component of the volatile matter is water
Bibliography
| 1 | ISO 4618:2006, Paints and varnishes — Terms and definitions |
| 2 | ISO 12000, Plastics/rubber — Polymer dispersions and rubber latices (natural and synthetic) — Definitions and review of test methods |