※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 2 部に規定されている規則に従って草案されています。
技術委員会の主な任務は、国際規格を作成することです。技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。
ISO 7270-2 は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 2, 試験および分析によって作成されました。
この第 2 版は、技術的に改訂された第 1 版 (ISO 7270-2:2005) を廃止し、置き換えます。
ISO 7270 は、「ゴム — 熱分解ガスクロマトグラフィー法による分析」という一般タイトルの下、次の部分で構成されています。
- Part 1: ポリマーの同定 (単一ポリマーおよびポリマーブレンド)
- Part 2: スチレン/ブタジエン/イソプレン比の決定
警告ISO 7270 のこの部分を使用する人は、通常の実験室での実践に精通している必要があります。 ISO 7270 のこの部分は、その使用に関連する安全上の問題があったとしても、そのすべてに対処することを目的としたものではありません。適切な安全衛生慣行を確立し、国の規制条件を確実に遵守することはユーザーの責任です。
注意ISO 7270 のこの部分で指定されている特定の手順には、局所的な環境危険を引き起こす可能性のある物質の使用または生成、または廃棄物の生成が含まれる場合があります。使用後の安全な取り扱いと廃棄については、適切な文書を参照する必要があります。
1 スコープ
ISO 7270 のこの部分では、生ゴム、未加硫または加硫コンパウンド中のコポリマー、ホモポリマーおよび/またはコポリマーのブレンドにおけるスチレン/ブタジエン/イソプレン比を測定するための熱分解ガスクロマトグラフィー法を規定しています。スチレン、ブタジエン、イソプレンからなるコポリマー/ターポリマー、およびこれらのポリマーのブレンドに適用できます。
注 1 ISO 7270 のこの部分を使用するには、分析者が記載されている操作を実行し、結果を正しく解釈するために、ガスクロマトグラフィーの原理と技術に関する十分な知識が必要です。
注 2この試験方法で決定されるスチレン/ブタジエン/イソプレン比は、樹脂の存在と高レベルの硫黄の影響を受けます。
2 規範的参照
この文書を適用するためには、以下の参照文書が不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 1407:2011, ゴム - 溶媒抽出物の測定
参考文献
| 1 | ISO/TR 9272:1986, ゴムおよびゴム製品 — 試験方法規格の精度の決定(現在は廃止) |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7270-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis.
This second edition cancels and replaces the first edition (ISO 7270-2:2005), which has been technically revised.
ISO 7270 consists of the following parts, under the general title Rubber — Analysis by pyrolytic gas-chromatographic methods:
- Part 1: Identification of polymers (single polymers and polymer blends)
- Part 2: Determination of styrene/butadiene/isoprene ratio
WARNING Persons using this part of ISO 7270 should be familiar with normal laboratory practice. This part of ISO 7270 does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.
CAUTION Certain procedures specified in this part of ISO 7270 might involve the use or generation of substances, or the generation of waste, that could constitute a local environmental hazard. Reference should be made to appropriate documentation on safe handling and disposal after use.
1 Scope
This part of ISO 7270 specifies a pyrolytic gas-chromatographic method for the determination of the styrene/butadiene/isoprene ratio in copolymers, or blends of homopolymers and/or copolymers, in raw rubbers or in unvulcanized or vulcanized compounds. It is applicable to copolymers/terpolymers consisting of styrene, butadiene and isoprene, and blends of these polymers.
NOTE 1 The use of this part of ISO 7270 pre-supposes sufficient working knowledge of the principles and techniques of gas chromatography for the analyst to perform the operations described and interpret the results correctly.
NOTE 2 The styrene/butadiene/isoprene ratio determined by this test method is affected by the presence of resin and by a high level of sulfur.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 1407:2011, Rubber — Determination of solvent extract
Bibliography
| 1 | ISO/TR 9272:1986, Rubber and rubber products — Determination of precision for test method standards (now withdrawn) |