※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。
技術委員会によって採択された国際規格の草案は、ISO 理事会によって国際規格として承認される前に、承認のためにメンバー団体に回覧されます。それらは、投票するメンバー団体による少なくとも 75% の承認を必要とする ISO 手順に従って承認されます。
国際規格 ISO 7844 は、技術委員会 ISO/TC 59, 建物の建設によって作成されました。
ユーザーは、すべての国際規格が随時改訂されること、および他の国際規格への参照は、別段の記載がない限り、その最新版を意味することに注意する必要があります。
0 はじめに
大きなパネルを含む構造の分析は、壁要素間の垂直ジョイントによって果たすことができる役割の重要性を示しています。
最新の計算方法では、これらのジョイントの動作に関する十分な知識が利用できる場合に、これらのジョイントの影響を考慮することができます。したがって、この国際規格の目的は、動作の主要な要素を実験的に決定する方法を提供することです。これらの関節のいくつか。
この国際規格は、試験結果の解釈または使用を扱っていません。特に、これらは多くの場合実行することが困難な試験であるため、この国際規格は最小反復係数を指定していません。しかしながら、そのような試験の結果に影響を与えることが多いばらつきと、実際の状態を最もよく表す試験を数回繰り返すことが望ましいことに注意が必要です。
大型パネルで形成されたブレース壁の設計計算で考慮される、鉄筋コンクリート パネル間の垂直ジョイントの機械的特性は、接線方向荷重と当該ジョイントによって連結されたパネルの相対変位との関係によって表すことができます。
1 スコープ
この国際規格は、接線荷重を受ける大型鉄筋コンクリート パネル間の特定のタイプの垂直ジョイントの接線荷重と相対変位との関係を決定するための実験室の機械的試験方法を指定します。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the ISO Council. They are approved in accordance with ISO procedures requiring at least 75 % approval by the member bodies voting.
International Standard ISO 7844 was prepared by Technical Committee ISO/TC 59, Building construction.
Users should note that all International Standards undergo revision from time to time and that any reference made herein to any other International Standard implies its latest edition, unless otherwise stated.
0 Introduction
The analysis of structures comprising large panels has shown the importance of the role that can be played by vertical joints between wall elements.
Modem methods of calculation allow the influence of these joints to be taken into account when sufficient knowledge of their behaviour is available, and the purpose of this International Standard is, therefore, to provide a method for the experimental determination of the principal elements of the behaviour of some of these joints.
This International Standard does not deal with the interpretation or use of the test results. In particular, as these are tests which are often difficult to perform in large numbers, this International Standard does not specify a minimum repetition factor. Attention is drawn, however, to the dispersion which often affects the results of such tests and to the desirability of repeating several times those tests which are most representative of the real conditions.
The mechanical characteristics of vertical joints between reinforced concrete panels which are taken into account in design calculations for bracing walls formed of large panels can be expressed by means of the relationship between tangential loading and the relative displacement of the panels linked by the joint concerned.
1 Scope
This International Standard specifies a laboratory mechanical method of test for the determination of the relationship between tangential loading and relative displacement for certain types of vertical joints between large reinforced concrete panels subjected to tangential loading.