この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令で指定された規則に従って起草されます。 2.
技術委員会の主な任務は、国際規格を準備することです。技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
ISO 7963 は、技術委員会 ISO/TC 44, 溶接および関連プロセス、小委員会 SC 5, 溶接部の試験および検査によって作成されました。
この第 2 版は、技術的に改訂された第 1 版 (ISO 7963:1985) を取り消して置き換えるものです。
序章
校正ブロック番号2 は、ISO 2400 に記載されているものとはサイズと形状が異なります。
校正ブロック番号2 は非常に小さく軽量であり、ジオメトリははるかに単純です。
校正ブロック番号2 は、より大きなブロックほどの範囲を提供しません。特に、超音波探傷器を完全にチェックすることを意図したものではありません。
ただし、キャリブレーションブロックNo. 2 を使用すると、実際のテスト中に、時間軸の設定と超音波装置の感度を時々簡単に確認できます。また、小型斜角プローブのビーム角度やプローブインデックスの確認にも適しています。
注記校正ブロック番号1 は現在、EN 12223 で指定されています。
この国際規格のあらゆる側面の公式解釈の要求は、 www.iso.org にある完全なリストである、各国の標準化団体を通じて ISO/TC 44/SC 5 の事務局に送信する必要があります。
1 スコープ
この国際規格は、校正ブロック番号の寸法、材料、製造、および使用方法を指定します。 2 超音波試験装置の校正とチェック用。
2 参考文献
本書の適用には、以下の参考文献が不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
このドキュメントの目的のために、ISO 5577 に記載されている用語と定義が適用されます。
参考文献
| [1] | ISO 2400, 鋼の溶接 — 超音波検査用機器の校正用基準ブロック |
| [2] | EN 12223, 非破壊検査 — 超音波検査 — 校正ブロック No.1 の仕様 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
ISO 7963 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds.
This second edition cancels and replaces the first edition (ISO 7963:1985), which has been technically revised.
Introduction
Calibration block No. 2 differs in size and shape from that described in ISO 2400.
Calibration block No. 2 is very much smaller and lighter, and its geometry is much simpler.
Calibration block No. 2 does not offer as much scope as the larger block; in particular it is not meant to check an ultrasonic flaw detector completely.
However, calibration block No. 2 makes it possible, during practical testing, to check simply, from time to time, the setting of the time base and the sensitivity of the ultrasonic equipment. Moreover, it is suited to checking the beam angle and the probe index of miniature angle-beam probes.
NOTE Calibration block No. 1 is currently specified in EN 12223.
Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 5 via your national standards body, a complete listing which can be found at www.iso.org .
1 Scope
This International Standard specifies the dimensions, material, manufacture and methods of use for calibration block No. 2 for calibrating and checking ultrasonic testing equipment.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 4287, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
- ISO 5577, Non-destructive testing — Ultrasonic inspection — Vocabulary
- EN 10025-1, Hot rolled products of structural steels — 1: General technical delivery conditions
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5577 apply.
Bibliography
| [1] | ISO 2400, Welds in steel — Reference block for the calibration of equipment for ultrasonic examination |
| [2] | EN 12223, Non-destructive testing — Ultrasonic examination — Specification for calibration block No.1 |