※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の開発に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2 ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自発的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html .
この文書は、技術委員会 ISO/TC 20, 航空機および宇宙船、小委員会 SC 10, 航空宇宙流体システムおよびコンポーネントによって作成されました。
この第 4 版は、技術的に改訂された第 3 版 (ISO 8177:2015) を取り消して置き換えるものです。
主な変更点は次のとおりです。
- オメガ クランプの追加寸法は、表 2 に含まれています。
1 スコープ
この文書では、公称直径 5 mm の 2 本のボルトを使用して取り付けられるオメガ クランプ (サドル クランプ) の最大および最小寸法を指定します。
指定された寸法は、寸法エンベロープを定義します。このドキュメントは、互換性の標準ではありません。クランプの種類ごとの公差は、部品規格の図面に規定されています。
2 参考文献
このドキュメントには規範的な参照はありません。
3 用語と定義
このドキュメントには、用語と定義は記載されていません。
ISO および IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
参考文献
| [1] | ISO 6771, 航空宇宙 - 流体システムおよびコンポーネント - 圧力および温度分類 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 10, Aerospace fluid systems and components.
This fourth edition cancels and replaces the third edition (ISO 8177:2015), which has been technically revised.
The main changes are as follows:
- additional dimensions of omega clamps have been included in Table 2.
1 Scope
This document specifies maximum and minimum dimensions for omega clamps (saddle clamps) installed by means of two bolts with nominal diameters of 5 mm.
The specified dimensions define a dimensional envelope. This document is not an interchangeability standard. The tolerances for each type of clamp are defined in the drawings in the standards for parts.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
Bibliography
| [1] | ISO 6771, Aerospace — Fluid systems and components — Pressure and temperature classifications |