※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 2 部に規定されている規則に従って草案されています。
技術委員会の主な任務は、国際規格を作成することです。技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。
ISO 8296 は、技術委員会 ISO/TC 61, プラスチック、小委員会 SC 11, 製品によって作成されました。
この第 2 版は、第 1 版 (ISO 8296:1987) を取り消し、置き換えるものです。この第 2 版は、(ISO 8296:1987) のような「ワイヤー バー No. 2」ではなく、単に「ワイヤー バー」を指定する 4.1 の修正を含むマイナー リビジョンを構成します。初版)、7.2 の第 2 段落で液体が広がる面積を 20 cm 2から 6 cm 2に修正。
1 スコープ
1.1この国際規格は、特定の試験溶液の滴と接触するプラスチックフィルムおよびシートの表面の濡れ張力を測定する方法を指定します。
1.2プラスチック フィルムがインク、コーティング、接着剤などを保持する能力は主にその表面の特性に依存し、いくつかの表面処理技術の 1 つによって改善できます。これらの同じ処理技術は、溶媒の混合物と接触したプラスチックフィルム表面の濡れ張力を増加させることがわかっています。したがって、プラスチック フィルム表面の濡れ張力を、インク、コーティング、接着剤などを受け入れて保持する能力と関連付けることができます。特定のフィルム表面の測定された濡れ張力は、許容可能なインク、コーティング、または接着剤にのみ関連付けることができます。経験による定着。濡れ張力自体は、インク、コーティング、または接着剤の接着力の完全に許容できる尺度ではありません。
1.3フィルム表面の汚染および液体試薬中の微量の界面活性不純物は、ぬれ張力に影響を与える可能性があります。したがって、フィルム表面の試験対象部分に触れたりこすったりしないこと、すべての機器を入念に洗浄し、試薬の純度を注意深く管理することが重要です。特にガラス器具は、クロム硫酸や硫酸アンモニウムなどの酸化剤で洗浄するなど、洗剤を除去するための特別な予防措置を講じない限り、非常に強い表面張力低下能力を持つ洗剤で汚染される可能性があります。ペルオキシ二硫酸塩で洗浄し、蒸留水ですすぐ。
1.4試験材料の表面が試験溶液と化学反応する場合には、試験は適用されません。
1.5プラスチックフィルムやシートの表面特性は経年変化により変化する可能性があることに注意してください。したがって、測定値はフィルムの使用年数に関連している必要があります。
2 規範的参照
この文書を適用するためには、以下の参照文書が不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 291, プラスチック — 調整および試験用の標準雰囲気
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8296 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This second edition cancels and replaces the first edition (ISO 8296:1987), of which it constitutes a minor revision which included the correction of 4.1 to simply specify a"wire bar" (rather than"wire bar No. 2" as in the first edition) and correction of the area over which the liquid is spread in 7.2, second paragraph, from 20 cm2 to 6 cm2.
1 Scope
1.1 This International Standard specifies a method for determining the wetting tension of surfaces of plastic film and sheeting in contact with drops of specific test solutions.
1.2 The ability of plastic films to retain inks, coatings, adhesives, etc., is primarily dependent on the character of their surfaces, and can be improved by one of several surface-treatment techniques. These same treatment techniques have been found to increase the wetting tension of a plastic film surface in contact with mixtures of solvents. It is therefore possible to relate the wetting tension of a plastic film surface to its ability to accept and retain inks, coatings, adhesives, etc. The measured wetting tension of a specific film surface can only be related to acceptable ink, coating, or adhesive retention through experience. Wetting tension, in itself, is not a completely acceptable measure of ink, coating or adhesive adhesion.
1.3 Any contamination of the film surface and any trace of surface-active impurities in the liquid reagents may affect the wetting tension. It is therefore important that the portion of the film surface to be tested is not touched or rubbed, that all equipment be scrupulously clean, and that reagent purity be carefully controlled. Glass apparatus, in particular, is likely to be contaminated with detergents having very strong surface tension reducing ability, unless specific precautions are taken to ensure their absence such as by cleaning with an oxidizing agent, for example chromic-sulfuric acid or sulfuric acid-ammonium peroxydisulfate, and rinsing with distilled water.
1.4 The test is not applicable when the surface of the material to be tested reacts chemically with the test solution.
1.5 It should be noted that surface properties of plastic film and sheeting may change by ageing processes. The measurements must therefore be related to the age of the film.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 291, Plastics — Standard atmospheres for conditioning and testing