※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part 1 部に記載されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
ISO は、この文書の実装に特許の使用が含まれる可能性があることに注意を促しています。 ISO は、請求された特許権に関する証拠、有効性、または適用可能性に関していかなる立場もとりません。この文書の発行日の時点で、ISO はこの文書の実装に必要となる可能性のある特許の通知を受け取っていません。ただし、実装者は、これが www.iso.org/patents で入手可能な特許データベースから取得できる最新情報を表していない可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易の技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html
この文書は、技術委員会 ISO/TC 138 「流体輸送用プラスチック パイプ、継手およびバルブ」 、小委員会 SC 6 「すべての用途のための強化プラスチック パイプおよび継手」によって作成されました。
この第 4 版は、技術的に改訂された第 3 版 (ISO 8513:2016) を廃止し、置き換えるものです。
主な変更点は以下のとおりです。
- 6.2.3 項は、試験片を保持するグリップに関係なく、メーカーがサンプルのビルドアップ端を利用することを選択できるように修正されました (6.2.3 を参照)
1 スコープ
この文書では、ガラス強化熱硬化性プラスチック (GRP) パイプの長手方向の引張特性を測定するための 2 つの試験方法 (方法 A および方法 B) を規定しています。決定できるプロパティは次のとおりです。
- 縦方向の引張強さ、および
- 極限伸び率。
方法 A では、試験片としてパイプから切り出した長手方向の短冊を使用します。
方法 B では、パイプの全断面の指定された長さを使用します。
方法 A は、細断ガラスおよび/または織ロービングおよび/またはフィラーの有無にかかわらず、円周方向に巻かれたフィラメントを備えた公称サイズ DN 50 以上のパイプ、および遠心鋳造パイプに適用できます。公称サイズ DN 200 以上の螺旋状に巻かれたフィラメントを備えたパイプに適用できます。
方法 B はすべてのタイプの GRP パイプに適用できます。通常、呼び径 DN 150 以下のパイプに使用されます。
1 つの方法からの結果は、別の方法から得られた結果と必ずしも同じではありません。ただし、すべてのメソッドの有効性は同等です。
付録 A には、薄肉螺旋巻きパイプの試験に有用であることが判明した方法 B の追加の考慮事項が記載されており、基本テキストを補足するために使用できます。
注この文書では、縦引張弾性率の決定については説明しません。多くの GRP パイプは多層構造であるため、弾性率の決定に必要なひずみの正確な測定は非常に困難です。縦弾性率を決定したい場合は、ISO 527-4 および/または ISO 527-5 を参照してください。
2 規範的参照
この文書には規範的な参照はありません。
3 用語と定義
この文書の目的上、次の用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
螺旋状フィラメント巻き
十字傷
バランスのとれた巻き角度で作られたフィラメント巻きパイプ
3.2
縦引張強さ
σla *
σlblb
破壊時の単位平均円周あたりの長手方向の最大引張力
注記 1:円周 1 ミリメートルあたりのニュートン (N/mm) で表されます。
注記 2: 下付き文字 A および B は、使用された試験方法を示します。
3.3
平均円周
平均直径にπを乗じた値に相当する円周
グレード 1 から入門まで: π ≈ 3.141 6.
注記 2:ミリメートル (mm) で表されます。
3.4
平均直径
d m
パイプ壁の断面の中心に対応する円の直径
- a)パイプの外径の平均から壁の厚さの平均を引いたもの。
- b)パイプの外周を π (π ≈ 3.141 6) で割った値から壁の厚さの平均を引いた値。
- c)パイプの内径の平均と壁の厚さの平均を加算したもの。
注記 2:ミリメートル (mm) で表されます。
3.5
極限伸び
εLL
伸びは極限縦方向引張強さと一致します。
注記 1:この文書の目的上、伸びの測定は引張試験機のクロスヘッドの動きの測定に限定されます。
注記 2:試験片の初期標点間距離または自由長に対する百分率で表します。
参考文献
| 1 | ISO 527-4, プラスチック — 引張特性の測定 — Part 4: 等方性および異方性の繊維強化プラスチック複合材料の試験条件 |
| 2 | ISO 527-5, プラスチック — 引張特性の測定 — Part 5: 一方向繊維強化プラスチック複合材料の試験条件 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s) which may be required to implement this document. However, implementers are cautioned that this may not represent the latest information, which may be obtained from the patent database available at www.iso.org/patents . ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications.
This fourth edition cancels and replaces the third edition (ISO 8513:2016), which has been technically revised.
The main changes are as follows:
- subclause 6.2.3 has been modified to allow the manufacturer to choose to utilize built-up ends on the samples, independent of the grips holding the test piece (see 6.2.3).
1 Scope
This document specifies two test methods (method A and method B) for determining the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes. The properties which can be determined are:
- the longitudinal tensile strength, and
- the percentage ultimate elongation.
Method A uses, for the test piece(s), a longitudinal strip cut from a pipe.
Method B uses a specified length of the full cross-section of the pipe.
Method A is applicable to pipes with a nominal size of DN 50 or greater with circumferentially-wound filaments, with or without chopped glass and/or woven rovings and/or fillers, and to centrifugally-cast pipes. It is applicable to pipes with helically wound filaments with a nominal size of DN 200 or greater.
Method B is applicable to all types of GRP pipe. It is usually used for pipes with a nominal size up to and including DN 150.
Results from one method are not necessarily equal to the results derived from any of the alternative methods. However, all methods have equal validity.
Annex A describes additional considerations for method B that have been found useful for the testing of thin-walled helically-wound pipes and can be used to supplement the basic text.
NOTE This document does not address the determination of longitudinal tensile modulus. Due to the multi-layer construction of many GRP pipes, the accurate measurement of strain, necessary for modulus determination, can be very difficult. If it is desired to determine longitudinal modulus, see ISO 527-4 and/or ISO 527-5.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
3.1
helically filament-wound
cross wound
filament-wound pipes made with a balanced winding angle
3.2
longitudinal tensile strength
σla*
σlb*
maximum tensile force in the longitudinal direction per unit mean circumference at failure
Note 1 to entry: It is expressed in newtons per millimetre of the circumference (N/mm).
Note 2 to entry: The subscripts A and B denote the method of test used.
3.3
mean circumference
circumference corresponding to the mean diameter multiplied by π
Note 1 to entry: π ≈ 3,141 6.
Note 2 to entry: It is expressed in millimetres (mm).
3.4
mean diameter
dm
diameter of the circle corresponding with the middle of the pipe wall cross-section
- a) the average of the external diameter of the pipe minus the average of the wall thickness;
- b) the external circumference of the pipe divided by π (π ≈ 3,141 6) minus the average of the wall thickness;
- c) the average of the internal diameter of the pipe plus the average of the wall thickness.
Note 2 to entry: It is expressed in millimetres (mm).
3.5
ultimate elongation
εL
elongation coincident with the ultimate longitudinal tensile strength.
Note 1 to entry: For the purposes of this document, the measurement of elongation is limited to measurement of the movement of the tensile testing machine cross-heads.
Note 2 to entry: It is expressed as a percentage of an initial gauge length or free length of a test piece.
Bibliography
| 1 | ISO 527-4, Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| 2 | ISO 527-5, Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites |