※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
国際規格 ISO 8526-1 は、技術委員会 ISO/TC 39, Machine tools によって作成されました。
ISO 8526 は、次の部分で構成されており、一般的なタイトルは「工作機械用モジュラー ユニット - ワーク保持パレット」です。
- Part 1: 公称サイズ 800 mm までのワーク保持パレット
- Part 2: 公称サイズが 800 mm を超えるワーク保持パレット
附属書 A は、ISO 8526 のこの部分の不可欠な部分を形成します。附属書 B は情報提供のみを目的としています。
序章
ISO 8526 のこの部分は、さまざまなメーカーのパレットを含め、ワーク保持パレットの互換性を促進するために作成されました。縦横比1.25, 公称800mmまでの正方形パレットと長方形パレットに対応しています。
ISO 8526 のこの部分で指定されているよりも厳しい公差のパレットが必要な場合は、製造業者とユーザーの間の合意に従う必要があります。
ISO 8526 のこの部分は、パレットの位置決め精度を指定していません。
1 スコープ
ISO 8526 のこのパートでは、工作機械や製造システムで使用するワーク保持パレットの寸法を指定しています。
以下の公称サイズのパレットに適用されます。
320mm, 400mm, 500mm, 630mm, 800mm
2 参考文献
以下の規格には規定が含まれており、このテキストで参照することにより、ISO 8526 のこの部分の規定を構成します。発行の時点で、示された版は有効でした。すべての規格は改訂される可能性があり、ISO 8526 のこの部分に基づく契約の当事者は、以下に示す規格の最新版を適用する可能性を調査することをお勧めします。 IEC および ISO のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 286-2:1988, 限界と適合の ISO システム — 2: 穴と軸の標準公差等級と限界偏差の表。
- ISO 299:1987, 工作機械テーブル — T スロットおよび対応するボルト。
- ISO 1101:1983, 技術図面 — 幾何公差 — 形状、方向、位置および振れの公差 — 一般性、定義、記号、図面の表示。
- ISO 2768-1:1989, 一般公差 — 1: 個々の公差表示のない直線寸法と角度寸法の公差。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 8526-1 was prepared by Technical Committee ISO/TC 39, Machine toots.
ISO 8526 consists of the following parts, under the general title Modular units for machine tools — Workholding pallets:
- Part 1: Workholding pallets up to 800 mm nominal size
- Part 2: Workholding pallets of nominal size greater than 800 mm
Annex A forms an integral part of this part of ISO 8526. Annex B is for information only.
Introduction
This part of ISO 8526 has been drawn up to facilitate interchangeability of workholding pallets, including those from different manufacturers. It deals with square pallets and rectangular pallets of length-to-width ratio of 1,25 and of nominal size up to 800 mm.
If pallets with tighter tolerances than specified in this part of ISO 8526 are required, they shall be subject to agreement between the manufacturer and user.
This part of ISO 8526 does not specify the positioning accuracy of the pallets.
1 Scope
This part of ISO 8526 specifies the dimensions of workholding pallets for use with machine tools and in manufacturing systems.
It applies to the following nominal sizes of pallet:
320mm, 400 mm, 500 mm, 630 mm and 800 mm
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 8526. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 8526 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
- ISO 286-2:1988, ISO system of limits and fits — 2: Tables of standard tolerance grades and limit deviations for holes and shafts.
- ISO 299:1987, Machine tool tables — T-slots and corresponding bolts.
- ISO 1101:1983, Technical drawings — Geometrical tolerancing — Tolerancing of form, orientation, location and run-out — Generalities, definitions, symbols, indications on drawings.
- ISO 2768-1:1989, General tolerances — 1: Tolerances for linear and angular dimensions without individual tolerance indications.