※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part に規定されている規則に従って草案されています。
技術委員会の主な任務は、国際規格を作成することです。技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。
ISO 9311-3 は、欧州標準化委員会 (CEN) 技術委員会 CEN/TC 193, 接着剤、技術委員会 ISO/TC 138, 流体輸送用プラスチックパイプ、継手およびバルブ、小委員会 SC 5 と協力して作成されました。 ISO と CEN 間の技術協力に関する協定 (ウィーン協定) に基づく、プラスチック材料のパイプ、継手、バルブおよびその付属品の一般特性 - 試験方法と基本仕様。
ISO 9311 は、一般タイトル「熱可塑性配管システム用接着剤」の下に、次の部分で構成されています。
- Part 1: フィルムの特性の決定
- Part 2: せん断強度の決定
- Part 3: 内圧耐性を測定するための試験方法
1 スコープ
ISO 9311 のこの部分では、熱可塑性プラスチック配管システム用の接着剤で作られたアセンブリの内圧耐性を評価する方法が規定されています。
2 規範的参照
この文書を適用するためには、以下の参照文書が不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 1167:1996, 流体輸送用熱可塑性プラスチックパイプ - 内圧に対する耐性 - 試験方法
- EN 923, 接着剤 - 用語と定義
- EN 1066, 接着剤 - サンプリング
- EN 1067, 接着剤 — 試験用サンプルの検査と準備
3 用語と定義
この文書の目的のために、EN 923 および以下に示されている用語と定義が適用されます。
3.1
設定時間
接着剤を塗布してから試験を開始するまでの時間
3.2
直径すきま
パイプの平均外径とソケットの平均内径の直径の差
参考文献
| 1 | ISO 15605, 接着剤 - サンプリング |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9311-3 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 193, Adhesives, in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories — Test methods and basic specifications, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
ISO 9311 consists of the following parts, under the general title Adhesives for thermoplastic piping systems:
- Part 1: Determination of film properties
- Part 2: Determination of shear strength
- Part 3: Test method for the determination of resistance to internal pressure
1 Scope
This part of ISO 9311 specifies a method for the assessment of the internal pressure resistance of assemblies made with adhesives for thermoplastic piping systems.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 1167:1996, Thermoplastics pipes for the conveyance of fluids — Resistance to internal pressure — Test method
- EN 923, Adhesives — Terms and definitions
- EN 1066, Adhesives — Sampling
- EN 1067, Adhesives — Examination and preparation of samples for testing
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 923 and the following apply.
3.1
setting time
time between applying the adhesive and the beginning of the test
3.2
diametrical clearance
difference in diameter between mean outside diameter of the pipe and mean inside diameter of the socket
Bibliography
| 1 | ISO 15605, Adhesives — Sampling |