※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令Part 3 部に規定されている規則に従って草案されています。
技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
この国際規格の要素の一部が特許権の対象となる可能性が注目されています。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。
国際規格 ISO 9633 は、ISO/TC 100動力伝達およびコンベヤ用チェーンおよびチェーンホイール技術委員会によって作成されました。
この第 2 版は、サイクル チェーンの設計と製造の改善を反映して改訂された第 1 版 (ISO 9633:1992) を廃止し、置き換えるものです。この版では、082 C チェーンの最小引張強度を低く指定し、ピンの押し出し抵抗の測定を扱います。
この国際規格の附属書 A は情報提供のみを目的としています。
1 スコープ
この国際規格は、サイクル チェーンの寸法と機械的特性、およびこれらの機械的特性 (ねじれ、横方向の偏り、スティッフ リンク、サイド バウ) を測定するための試験方法を指定します。
注記サイクルチェーンのスプロケットの寸法は ISO 606 に規定されています。
2 基準参照
以下の規範文書には、本文中の参照を通じてこの国際規格の規定を構成する規定が含まれています。日付が古い参照については、これらの出版物に対するその後の修正または改訂は適用されません。ただし、この国際規格に基づく協定の当事者は、以下に示す規範文書の最新版を適用する可能性を調査することが推奨されます。日付のない参照については、参照されている規範文書の最新版が適用されます。 ISO および IEC のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 606:1994, ショートピッチ伝動精密ローラーチェーンおよびチェーンホイール。
3 用語と定義
この国際規格の目的のために、次の用語と定義が適用されます。
3.1
横ずれ
実際のチェーンの中心線が直線でない状態
3.2
サイドボウ
チェーンが内部公差で許容される最大量まで横方向にたわんだときに、チェーンピンの平面に平行な平面内でチェーンがとる円弧の高さを特徴とする状態。
3.3
硬いリンク
チェーンリンクが、隣接する2つのリンクの配列軸から左右に60°の角度でスムーズに関節できない状態
3.4
ねじれ
チェーンリンクの関節軸が同一平面上にない状態
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 9633 was prepared by Technical Committee ISO/TC 100, Chains and chain wheels for power transmission and conveyors.
This second edition cancels and replaces the first edition (ISO 9633:1992), which has been revised to reflect improvements in the design and manufacture of cycle chains. This edition specifies a lower minimum tensile strength for 082 C chains and deals with the measurement of pin push-out resistance.
Annex A of this International Standard is for information only.
1 Scope
This International Standard specifies the dimensions and mechanical properties of cycle chains, as well as test methods for determining these mechanical properties (i.e. twist, lateral deviation, stiff link and side bow).
NOTE The dimensions of sprockets for cycle chains are specified in ISO 606.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
- ISO 606:1994, Short-pitch transmission precision roller chains and chain wheels.
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
lateral deviation
condition when the actual centreline of the chain is not straight
3.2
side bow
condition characterized by the height of an arc assumed by the chain in a plane parallel to the plane of the chain pins, when the chain is laterally deflected to the maximum extent permitted by its internal tolerances
3.3
stiff link
condition when a chain link cannot be articulated smoothly through an angle of 60°, to the right and to the left, from the alignment axis of the two adjacent links
3.4
twist
condition when the axes of articulation of the chain links are not in the same plane