※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part 1 部に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました 。 www.iso.org/directives
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます。 www.iso.org/patents
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
この文書を担当する委員会は、ISO/TC 96, クレーン、サブ委員会 SC 9, 橋梁およびガントリー クレーンです。
この第 3 版は、技術的に改訂された第 2 版 (ISO 9927-1:2009) を廃止し、置き換えるものです。
ISO 9927 は、 「クレーン — 検査」という一般タイトルのもと、次の部分で構成されています。
- Part 1: 一般
- Part 3: タワークレーン
ブリッジクレーンとガントリークレーンは将来のPart 5 の主題となる予定です。その他の部分も計画されています。
1 スコープ
この国際規格は、ISO 4306-1 で定義されているクレーンで実施される検査の一般要件を指定します。特定のタイプのクレーンに対する追加要件は、ISO 9927 の関連する特定の部分でカバーされることを目的としています。
2 規範的参照
以下の文書は、全部または一部がこの文書で規範的に参照されており、その適用には不可欠です。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 430, クレーン — 語彙
- ISO 4310, クレーン — テストコードと手順
- ISO 8686, クレーン – 荷重と荷重の組み合わせの設計原則
- ISO 10245-1, クレーン — 制限および指示装置 — Part 1: 一般
- ISO 12480-1, クレーン — 安全な使用 — Part 1: 一般
- ISO 12482-1, クレーン — 状態監視 — Part 1: 一般
- ISO 23814, クレーン — クレーン検査員の能力要件
3 用語と定義
この文書の目的上、ISO 4306 および以下の用語と定義が適用されます。
3.1
重要なコンポーネント
そのコンポーネントが故障すると、クレーンを使用している人、またはその近くにいる人の健康と安全に危険をもたらす可能性があります。
3.2
デザインライフ
特別な評価と一般的なオーバーホールが必要になる前に、元の設計仕様に基づいて応力サイクルと応力集合体 (設計制約) を考慮したクレーンの許容耐用年数を推定します。
注記 1:クレーン全体の設計寿命は、通常、限られた数の重要なコンポーネントの寿命によって決まります (ISO 12482‑1 を参照)
注記 2: 耐用年数中に受ける応力サイクルや応力集合が予想から外れる場合、設計寿命は推定値と異なる場合があります。
3.3
検査
必要に応じてテストを含む、クレーンの検査に関連するすべての活動
3.4
ユーザー組織の指示
ユーザー組織が発行するクレーンの使用説明書
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
The committee responsible for this document is ISO/TC 96, Cranes, Subcommittee SC 9, Bridge and gantry cranes.
This third edition cancels and replaces the second edition (ISO 9927-1:2009), which has been technically revised.
ISO 9927 consists of the following parts, under the general title Cranes — Inspections:
- Part 1: General
- Part 3: Tower cranes
Bridge and gantry cranes are to form the subject of a future Part 5. Other parts are planned.
1 Scope
This International Standard specifies the general requirements for inspections to be carried out on cranes as defined in ISO 4306-1. Additional requirements for particular types of cranes are intended to be covered by relevant specific parts of ISO 9927.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 4306 (all parts), Cranes — Vocabulary
- ISO 4310, Cranes — Test code and procedures
- ISO 8686, Cranes – Design principles for loads and load combinations
- ISO 10245-1, Cranes — Limiting and indicating devices — Part 1: General
- ISO 12480-1, Cranes — Safe use — Part 1: General
- ISO 12482-1, Cranes — Condition monitoring — Part 1: General
- ISO 23814, Cranes — Competency requirements for crane inspectors
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4306 and the following apply:
3.1
critical component
component, the failure of which would result in a risk to the health and safety of persons using the crane or located in its vicinity
3.2
design life
estimation of the allowable service life of a crane based on its original design specifications and taking into consideration the stress cycles and stress collectives (design constraints) before a special assessment and general overhaul are required
Note 1 to entry: The design life of a crane as a whole is usually governed by the life of a limited number of critical components (see ISO 12482‑1).
Note 2 to entry: The design life may vary from the estimation if the stress cycles and stress collectives experienced during its service life deviate from those expected.
3.3
inspection
all relevant activities for the inspection of a crane including testing, as applicable
3.4
user organization instructions
instructions issued by the user organization for the use of the crane