※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part 1 部に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、 www.iso.org/iso/foreword.html を参照してください。
この文書は、積層造形に関する共通の ISO/ASTM 標準セットを作成することを目的として、ISO と ASTM International の間のパートナーシップ協定に基づいて、ISO/TC 261「積層造形」と ASTM F 42「積層造形技術」の協力により作成されました。
ISO/ASTM 52903 シリーズのすべての部品のリストは、ISO の Web サイトでご覧いただけます。
1 スコープ
この文書では、押出ベースの積層造形 (AM) プロセスで使用されるプラスチック材料の要件を定義する方法について説明します。材料には、部品への加工に適した非充填、充填、および強化プラスチック材料が含まれます。これらの材料には、特殊な添加剤 (難燃剤、安定剤など) が含まれる場合もあります。プロセスには、すべての材料押出ベースの AM プロセスが含まれます。
この文書は、材料押出ベースの AM を使用する材料、原料、プラスチック部品、またはこれら 3 つの組み合わせの製造業者による使用を目的としています。
注場合によっては、材料メーカーが原料メーカーになることもあります。他の場合には、材料メーカーが材料 (例: ペレット) を原料メーカー (例: ペレットからフィラメントへのコンバーター) に供給することができます。
この文書は、その使用に関連する安全上の懸念がある場合、そのすべてに対処することを目的とするものではありません。適切な安全と健康、および環境慣行を確立し、使用前に規制上の制限の適用可能性を判断することは、この規格のユーザーの責任です。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO/ASTM 52900, 積層造形 — 一般原則 — 基礎と用語
3 用語と定義
この文書の目的のために、ISO/ASTM 52900 および以下に示されている用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
フィラメント
均一な断面に対して極端な長さを特徴とする原料
3.2
ペレット
所定のバッチ内で比較的均一な寸法を有する、少量の予備成形原料材料
注記 1:より小さいサイズのペレットは、マイクロペレットと呼ばれることもあります。
参考文献
| 1 | ASTM D149, 商用電源周波数における固体電気絶縁材料の絶縁破壊電圧および絶縁耐力の試験方法 |
| 2 | ASTM D150, 固体電気絶縁体の AC 損失特性および誘電率 (誘電率) の試験方法 |
| 3 | ASTM D256, プラスチックのアイゾット振子衝撃耐性を測定するための試験方法 |
| 4 | ASTM D257, 絶縁材料の DC 抵抗またはコンダクタンスの試験方法 |
| 5 | ASTM D638, プラスチックの引張特性の試験方法 |
| 6 | ASTM D648, エッジワイズ位置での曲げ荷重下でのプラスチックのたわみ温度の試験方法 |
| 7 | ASTM D696, シリカガラス膨張計を使用した、-30 °C から 30 °C までのプラスチックの線熱膨張係数の試験方法 |
| 8 | ASTM D785, プラスチックおよび電気絶縁材料のロックウェル硬度の試験方法 |
| 9 | ASTM D790, 非強化および強化プラスチックおよび電気絶縁材料の曲げ特性の試験方法 |
| 10 | ASTM D1238, 押出プラストメータによる熱可塑性プラスチックのメルトフローレートの試験方法 |
| 11 | ASTM D1525, プラスチックのビカット軟化温度の試験方法 |
| 12 | ASTM D1895, プラスチック材料の見掛け密度、かさ係数、および注入性の試験方法 |
| 13 | ASTM D1921, プラスチック材料の粒子サイズの試験方法 (ふるい分析) |
| 14 | ASTM D3935, ポリカーボネート (PC) 非充填強化材料の分類システムと仕様の根拠 |
| 15 | ASTM D4000, プラスチック材料を指定するための分類システム |
| 16 | ASTM D4673, アクリロニトリル-ブタジエン-スチレン(ABS)プラスチックおよび合金の成形および押出材料の分類システムおよび仕様の基礎 |
| 17 | ASTM D5205, ポリエーテルイミド (PEI) 材料の分類システムと仕様の基礎 |
| 18 | ASTM E11, 織線試験ふるい布および試験ふるいの仕様 |
| 19 | ASTM E831, 熱機械分析による固体材料の線形熱膨張の試験方法 |
| 20 | ISO 62, プラスチック - 吸水率の測定 |
| 21 | ISO 75-2, プラスチック — 荷重たわみ温度の決定 — Part 2: プラスチックとエボナイト |
| 22 | ISO 178, プラスチック - 曲げ特性の測定 |
| 23 | ISO 179-1, プラスチック — シャルピー衝撃特性の測定 — Part 1: 計器を使用しない衝撃試験 |
| 24 | ISO 179-2, プラスチック — シャルピー衝撃特性の測定 — Part 2: 計装衝撃試験 |
| 25 | ISO 306, プラスチック - 熱可塑性材料 - ビカット軟化温度 (VST) の測定 |
| 26 | ISO 527-1, プラスチック — 引張特性の決定 — Part 1: 一般原則 |
| 27 | ISO 1133-1, プラスチック — 熱可塑性プラスチックのメルトマスフローレート (MFR) およびメルトボリュームフローレート (MVR) の決定 — Part 1: 標準方法 |
| 28 | ISO 6186, プラスチック - 注ぐ性の測定 |
| 29 | ISO 8130-1, コーティングパウダー - Part 1: ふるい分けによる粒度分布の測定 |
| 30 | ISO 9001, 品質マネジメントシステム — 要件 |
| 31 | ISO 11359-2, プラスチック — 熱機械分析 (TMA) — Part 2: 線熱膨張係数とガラス転移温度の決定 |
| 32 | ISO 13485, 医療機器 - 品質管理システム - 規制目的の要件 |
| 33 | ISO 1043-1, プラスチック — 記号と略語 — Part 1: 基本ポリマーとその特殊な特性 |
| 34 | ISO 2580-1, プラスチック — アクリロニトリル-ブタジエン-スチレン (ABS) 成形材料および押出材料 — Part 1: 指定システムと仕様の根拠 |
| 35 | ISO 7391-1, プラスチック — ポリカーボネート (PC) 成形および押出材料 — Part 1: 指定システムと仕様の根拠 |
| 36 | ISO 19062-1, プラスチック — アクリロニトリル・ブタジエン・スチレン (ABS) 成形材料および押出材料 — Part 1: 指定システムと仕様の根拠 |
| 37 | ISO 21305-1, プラスチック — ポリカーボネート (PC) 成形および押出材料 — Part 1: 指定システムと仕様の根拠 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html .
This document was prepared by ISO/TC 261, Additive manufacturing, in cooperation with ASTM F 42, Additive manufacturing technologies, on the basis of a partnership agreement between ISO and ASTM International with the aim to create a common set of ISO/ASTM standards on additive manufacturing.
A list of all parts in the ISO/ASTM 52903 series can be found on the ISO website.
1 Scope
This document describes a method for defining requirements for plastic materials used in extrusion-based additive manufacturing (AM) processes. Materials include unfilled, filled, and reinforced plastic materials suitable for processing into parts. These materials can also contain special additives (e.g. flame retardants, stabilizers, etc.). Processes include all material extrusion-based AM processes.
This document is intended for use by manufacturers of materials, feedstocks, plastic parts or any combination of the three using material extrusion-based AM.
NOTE In some cases, material manufacturers can also be feedstock manufacturers. In other cases, a material manufacturer can supply materials (example: pellets) to a feedstock manufacturer (example: converter of pellets into filaments).
This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health, and environmental practices and determine the applicability of regulatory limitations prior to use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO/ASTM 52900, Additive Manufacturing — General Principles — Fundamentals and vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/ASTM 52900 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1
filament
feedstock characterized by extreme length relative to its uniform cross section
3.2
pellets
small mass of preformed feedstock material, having relative uniform dimensions in any given batch
Note 1 to entry: Pellets of smaller size can sometimes be referred to as micro-pellets.
Bibliography
| 1 | ASTM D149, Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies |
| 2 | ASTM D150, Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| 3 | ASTM D256, Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
| 4 | ASTM D257, Test Methods for DC Resistance or Conductance of Insulating Materials |
| 5 | ASTM D638, Test Method for Tensile Properties of Plastics |
| 6 | ASTM D648, Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position |
| 7 | ASTM D696, Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30 °C and 30 °C with a Vitreous Silica Dilatometer |
| 8 | ASTM D785, Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
| 9 | ASTM D790, Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| 10 | ASTM D1238, Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| 11 | ASTM D1525, Test Method for Vicat Softening Temperature of Plastics |
| 12 | ASTM D1895, Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials |
| 13 | ASTM D1921, Test Methods for Particle Size (Sieve Analysis) of Plastic Materials |
| 14 | ASTM D3935, Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
| 15 | ASTM D4000, Classification System for Specifying Plastic Materials |
| 16 | ASTM D4673, Classification System and Basis for Specification for Acrylonitrile-Butadiene-Styrene(ABS) Plastics and Alloys Molding and Extrusion Materials |
| 17 | ASTM D5205, Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| 18 | ASTM E11, Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| 19 | ASTM E831, Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis |
| 20 | ISO 62, Plastics — Determination of water absorption |
| 21 | ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| 22 | ISO 178, Plastics — Determination of flexural properties |
| 23 | ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| 24 | ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test |
| 25 | ISO 306, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| 26 | ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles |
| 27 | ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method |
| 28 | ISO 6186, Plastics — Determination of pourability |
| 29 | ISO 8130-1, Coating powders — Part 1: Determination of particle size distribution by sieving |
| 30 | ISO 9001, Quality management systems — Requirements |
| 31 | ISO 11359-2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| 32 | ISO 13485, Medical devices — Quality management systems — Requirements for regulatory purposes |
| 33 | ISO 1043-1, Plastics —Symbols and abbreviated terms —Part 1: Basic polymers and their special characteristics |
| 34 | ISO 2580-1, Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| 35 | ISO 7391-1, Plastics — Polycarbonate (PC) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| 36 | ISO 19062-1, Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| 37 | ISO 21305-1, Plastics — Polycarbonate (PC) moulding and extrusion materials — Part 1: Designation system and basis for specification |