9
B 0124 : 2009
表4−軸受,軌道輪及び軌道盤の寸法並びに寸法差に関する量記号(続き)
用語番号
番号 量記号 量及び定義 対応英語(参考)
JIS B 0104 JIS B 1515-1
2.45 VDmp 平面内平均外径の不同 05.01.10 5.2.11 variation of mean outside diameter
2.46 VDs 外径不同 05.01.04 5.2.5 variation of outside diameter
2.47 VDsp 平面内外径不同 05.01.09 5.2.10 variation of outside diameter in
a single plane
2.48 Vdmp 平面内平均内径の不同 05.01.10 5.1.11 variation of mean bore diameter
2.49 Vds 内径不同 05.01.04 5.1.5 variation of bore diameter
2.50 Vdsp 平面内内径不同 05.01.09 5.1.10 variation of bore diameter in a single
plane
2.51 α 呼び接触角 04.02.10 − nominal contact angle
2.52 内輪テーパ穴の角度 − − angle of taper (half the cone angle) f
(テーパ角度の1/2) inner ring bore
2.53 ΔBs 実測内輪幅の寸法差 05.02.03 5.3.3 deviation of a single inner ring width
2.54 実測軸軌道盤高さの寸法差 − − deviation of a single shaft washer
height
2.55 ΔCs 実測外輪幅の寸法差 05.02.03 5.3.3 deviation of a single outer ring width
2.56 実測ハウジング軌道盤高さ − − deviation of a single housing washer
の寸法差 height
2.57 ΔC1s 実測外輪フランジ幅の寸法 − 5.3.8 deviation of a single outer ring flange
差 width
2.58 ΔDm 平均外径の寸法差 05.01.06 5.2.7 deviation of mean outside diameter
2.59 ΔDmp 平面内平均外径の寸法差 05.01.08 5.2.9 deviation of mean outside diameter in
a single plane
2.60 ΔDs 実測外径の寸法差 05.01.03 5.2.4 deviation of a single outside diameter
2.61 ΔD1s 実測フランジ外径の寸法差 − − deviation of a single outside diameter
of outer ring flange
2.62 Δdm 平均内径の寸法差 05.01.06 5.1.7 deviation of mean bore diameter
2.63 Δdmp 平面内平均内径の寸法差 05.01.08 5.1.9 deviation of mean bore diameter in a
single plane
2.64 Δds 実測内径の寸法差 05.01.03 5.1.4 deviation of a single bore diameter
2.65 ΔTs 実組立[軸受]幅の寸法差 05.02.08 5.3.12 deviation of the actual (assembled)
bearing width
2.66 実軸受高さの寸法差 05.02.10 5.3.15 deviation of the actual bearing height
――――― [JIS B 0124 pdf 11] ―――――
10
B 0124 : 2009
表5−軸受,軌道輪及び軌道盤の円周振れに関する量記号
用語番号
番号 量記号 量及び定義 対応英語(参考)
JIS B 0104 JIS B 1515-1
3.01 Ke 外輪軌道の厚さ不同 05.07.11 6.4.2 variation in thickness between outer
ring raceway and outside surface
3.02 Kea 外輪のラジアル振れ 05.07.02 7.1.2 radial runout of outer ring of
assembled bearing
3.03 Ki 内輪軌道の厚さ不同 05.07.10 6.4.1 variation in thickness between inner
ring raceway and bore
3.04 Kia 内輪のラジアル振れ 05.07.01 7.1.1 radial runout of inner ring of
assembled bearing
3.05 Kiaa 内輪の非同期ラジアル振れa) − 7.1.3 asynchronous radial runout of inner
ring of assembled bearing
3.06 SD 側面に対する外輪外径面の 05.07.09 6.3.2 perpendicularity of outer ring outside
直角度 surface with respect to the face
3.07 SD1 フランジ背面に対する外輪 − 6.3.3 perpendicularity of outer ring outside
外径面の直角度 surface with respect to the flange back
face
3.08 Sd 内径の軸線に対する内輪側 05.07.07 6.3.1 perpendicularity of inner ring face with
面の直角度 respect to the bore
3.09 Sdr 側面に対する内輪内径の直 − − perpendicularity of inner ring bore with
角度 respect to the face
3.10 Se 側面に対する外輪軌道の平 05.07.08 6.2.2 parallelism of outer ring raceway with
行度 respect to the face
3.11 ハウジング軌道盤の軌道の 05.07.12 6.4.4 variation in thickness between housing
厚さ不同 washer raceway and back face
3.12 Sea 外輪のアキシアル振れ(ラジ 05.07.05 7.2.3 axial runout of outer ring of assembled
アル玉軸受) bearing (radial groove ball bearing)
3.13 外輪のアキシアル振れ(円す 05.07.06 7.2.4 axial runout of outer ring of assembled
いころ軸受) bearing (tapered roller bearing)
3.14 Sea1 外輪フランジ背面のアキシ − 7.2.5 axial runout of outer ring flange back
アル振れ(ラジアル玉軸受) face of assembled bearing (radial
groove ball bearing)
3.15 外輪フランジ背面のアキシ − 7.2.6 axial runout of outer ring flange back
アル振れ(円すいころ軸受) face of assembled bearing (tapered
roller bearing)
3.16 Si 側面に対する内輪軌道の平 05.07.08 6.2.1 parallelism of inner ring raceway with
行度 respect to the face
3.17 軸軌道盤の軌道の厚さ不同 05.07.12 6.4.3 variation in thickness between shaft
washer raceway and back face
3.18 Sia 内輪のアキシアル振れ(ラジ 05.07.03 7.2.1 axial runout of inner ring of assembled
アル玉軸受) bearing (radial groove ball bearing)
3.19 内輪のアキシアル振れ(円す 05.07.04 7.2.2 axial runout of inner ring of assembled
いころ軸受) bearing (tapered roller bearing)
注a) 非同期ラジアル振れは,非繰返し特性である。
――――― [JIS B 0124 pdf 12] ―――――
11
B 0124 : 2009
表6−サブユニットの寸法及び寸法差に関する量記号
用語番号
番号 量記号 量及び定義 JIS B JIS B 対応英語(参考)
0104 1515-1
4.01 Bc ラジアル保持器付き玉の保持器幅 − − cage width of a radial ball and cage assembly
4.02 ラジアル保持器付きころの保持器幅 cage width of a radial roller and cage assembly
4.03 Dc スラスト保持器付き玉の保持器外径04.04.19 − outside diameter of a thrust ball and cage
assembly
4.04 スラスト保持器付きころの保持器外 outside diameter of a thrust roller and cage
径 assembly
4.05 スラスト保持器付き針状ころの保持 outside diameter of a thrust needle roller and
器外径 cage assembly
4.06 Dpw 玉セットのピッチ径 04.04.10 − pitch diameter of a ball set
4.07 ころセットのピッチ径 04.04.11 pitch diameter of a roller set
4.08 dc スラスト保持器付き玉の保持器内径04.04.18 − bore diameter of a thrust ball and cage assembly
4.09 スラスト保持器付きころの保持器内 bore diameter of a thrust roller and cage
径 assembly
4.10 スラスト保持器付き針状ころの保持 bore diameter of a thrust needle roller and cage
器内径 assembly
4.11 E 外輪軌道径 − − raceway diameter of outer ring
4.12 外輪小端径(円すいころ軸受) 04.04.03 outer ring small inside diameter
4.13 Ew 玉コンプリメントの呼び外接円径 04.04.12 5.2.12 nominal outside diameter of ball complement
04.04.14
4.14 ころコンプリメントの呼び外接円径04.04.13 nominal outside diameter of roller complement
04.04.15
4.15 Ewm 玉コンプリメントの平均外接円径 − 5.2.15 mean outside diameter of ball complement
4.16 ころコンプリメントの平均外接円径 mean outside diameter of roller complement
4.17 Ews 玉コンプリメントの実測外接円径 − 5.2.13 single outside diameter of ball complement
4.18 ころコンプリメントの実測外接円径 single outside diameter of roller complement
4.19 Ews max 玉コンプリメントの最大実測外接円 − 5.2.14 largest single outside diameter of ball
径 complement
4.20 ころコンプリメントの最大実測外接 largest single outside diameter of roller
円径 complement
4.21 F 内輪軌道径 − − raceway diameter of inner ring
4.22 Fw 玉コンプリメントの呼び内接円径 04.04.12 5.1.12 nominal bore diameter of ball complement
04.04.14
4.23 ころコンプリメントの呼び内接円径04.04.13 nominal bore diameter of roller complement
04.04.15
4.24 Fwm 玉コンプリメントの平均内接円径 − 5.1.15 mean bore diameter of ball complement
4.25 ころコンプリメントの平均内接円径 mean bore diameter of roller complement
4.26 Fws 玉コンプリメントの実測内接円径 − 5.1.13 single bore diameter of ball complement
4.27 ころコンプリメントの実測内接円径 single bore diameter of roller complement
――――― [JIS B 0124 pdf 13] ―――――
12
B 0124 : 2009
表6−サブユニットの寸法及び寸法差に関する量記号(続き)
用語番号
番号 量記号 量及び定義 対応英語(参考)
JIS B 0104 JIS B 1515-1
4.28 Fws min玉コンプリメントの最 − 5.1.14 smallest single bore diameter of ball
小実測内接円径 complement
4.29 ころコンプリメントの smallest single bore diameter of roller
最小実測内接円径 complement
4.30 H 偏心固定輪の偏心量 − − eccentricity of an eccentric locking
collar
4.31 内輪偏心面の偏心量 eccentricity of an inner ring eccentric
extension
4.32 T1 内輪サブユニットの呼 − 5.3.16 nominal effective width of inner
び有効幅(円すいころ軸 subunit (tapered roller bearing)
受)
4.33 T1s 内輪サブユニットの実 − 5.3.17 actual effective width of inner subunit
有効幅(円すいころ軸 (tapered roller bearing)
受)
4.34 T2 外輪呼び有効幅(円すい − 5.3.19 nominal effective width of outer ring
ころ軸受) (tapered roller bearing)
4.35 T2s 外輪実有効幅(円すいこ − 5.3.20 actual effective width of outer ring
ろ軸受) (tapered roller bearing)
4.36 ΔEwm 玉コンプリメントの平 − 5.2.16 deviation of mean outside diameter of
均外接円径の寸法差 ball complement
4.37 ころコンプリメントの deviation of mean outside diameter of
平均外接円径の寸法差 roller complement
4.38 ΔFwm 玉コンプリメントの平 − 5.1.16 deviation of mean bore diameter of
均内接円径の寸法差 ball complement
4.39 ころコンプリメントの deviation of mean bore diameter of
平均内接円径の寸法差 roller complement
4.40 ΔT1s 内輪サブユニットの実 − 5.3.18 deviation of the actual effective width
有効幅の寸法差(円すい of inner subunit (tapered roller
ころ軸受) bearing)
4.41 ΔT2s 外輪実有効幅の寸法差 − 5.3.21 deviation of the actual effective width
(円すいころ軸受) of outer ring (tapered roller bearing)
――――― [JIS B 0124 pdf 14] ―――――
13
B 0124 : 2009
表7−転動体の寸法及び寸法差に関する量記号
用語番号
番号 量記号 量及び定義 対応英語(参考)
JIS B 0104
5.01 Dw 玉の呼び直径 05.04.01 nominal ball diameter
5.02 ころの呼び直径 05.05.01 nominal roller diameter
5.03 Dwe 定格荷重の計算に用いるころ直径 − roller diameter applicable in the calculation of
load ratings
5.04 Dwm 玉の平均直径 05.04.03 mean ball diameter
5.05 DwmL 玉のロットの平均直径 05.04.06 mean diameter of ball lot
5.06 Dwmp ころの平面内平均直径 05.05.03 mean roller diameter in a single plane
5.07 Dws 玉の実測直径 05.04.02 single ball diameter
5.08 ころの実測直径 05.05.02 single roller diameter
5.09 Lw ころの呼び長さ 05.05.05 nominal roller length
5.10 Lwe ころ有効長さ 04.04.56 effective roller length
5.11 Lws ころの実長さ 05.05.06 actual roller length
5.12 S 玉のゲージ 05.04.09 ball gauge
5.13 ころのゲージ 05.05.07 roller gauge
5.14 SDw ころの端面振れ 05.05.51 runout of roller end face with respect to outside
surface
5.15 VDwL 玉のロットの直径の相互差 05.04.07 variation of ball lot diameter
5.16 ころのゲージロットの直径の相互差05.05.09 variation of roller gauge lot diameter
5.17 VDwmp ころの平面内平均直径の不同a) − variation of mean roller diameter
5.18 VDwp ころの平面内直径不同 05.05.04 variation of roller diameter in a single plane
5.19 VDws 玉の直径不同 05.04.04 variation of ball diameter
5.20 VLwL ころのゲージロットの長さの相互差 − variation of roller gauge lot length
5.21 ΔDwmL 玉のロットの平均直径の寸法差 05.04.51 deviation of mean diameter of ball lot
5.22 ΔDwmp ころの平面内平均直径の寸法差 − deviation of mean roller diameter in a single plane
5.23 ΔDws ころの実測直径の寸法差 − deviation of a single roller diameter
5.24 ΔLws ころの実測長さの寸法差 − deviation of a single roller length
5.25 ΔRw ころの真円度 05.06.01 deviation from circular form of roller outside
surface
5.26 ΔS 玉のゲージからのロットの寸法差 05.04.10 deviation of a ball lot from ball gauge
注a) 外径面の円筒部だけに適用する。
――――― [JIS B 0124 pdf 15] ―――――
次のページ PDF 16
JIS B 0124:2009の引用国際規格 ISO 一覧
- ISO 15241:2001(MOD)
JIS B 0124:2009の国際規格 ICS 分類一覧
- 21 : 一般的に使用される機械的システム及び構成要素 > 21.200 : 歯車
- 01 : 総論.用語.標準化.ドキュメンテーション > 01.080 : 図記号 > 01.080.30 : 機械及び建築用製図,ダイヤグラム,計画書,地図及び関連技術文書のための図記号
JIS B 0124:2009の関連規格と引用規格一覧
- 規格番号
- 規格名称
- JISB0104:1991
- 転がり軸受用語
- JISB1515-1:2006
- 転がり軸受―公差―第1部:用語及び定義
- JISZ8201:1981
- 数学記号
- JISZ8202-0:2000
- 量及び単位―第0部:一般原則